Accessories And Spare Parts; Scope Of Delivery; Safety Devices; Symbols On The Device - Kärcher CNS 36-35 Battery Manual De Instrucciones

period of use cannot be set, because this depends on
several influencing factors:
 Personal tendency to suffer from poor circulation
(frequently cold fingers, tingling sensation in the fin-
gers)
 Low ambient temperature. Wear warm gloves to
protect your hands.
 Holding the device too tightly hindering blood circu-
lation.
 Continuous operation is more harmful than opera-
tion interrupted by work breaks.
You should see a doctor if using the device regularly
and for lengthy periods of time, and in the event of re-
peated occurrences of symptoms such as tingling in
the fingers or cold fingers.
Intended use
DANGER
Improper use
Danger of death from incision injuries
Only use the device for its proper use.
 The chainsaw is only intended for private use.
 The chainsaw is intended for outdoor use.
 For safety reasons, always hold the chainsaw firmly
with both hands.
 The chainsaw was developed for sawing small
branches, large branches, trunks and beams. The
cutting length of the guide rail determines the maxi-
mum possible diameter of the sawed material.
 The chainsaw may only be used for cutting wood.
 Do not use the chainsaw in a wet environment or in
the rain.
 Use the chainsaw only in a well lit environment.
 Modifications and changes to the device that are not
authorised by the manufacturer are prohibited for
safety reasons.
Any other use is prohibited. The user shall be liable for
hazards arising as a result of improper use.
Environmental protection
The packing materials can be recycled. Please
dispose of packaging in accordance with the en-
vironmental regulations.
Electrical and electronic appliances contain valu-
able, recyclable materials and often components
such as batteries, rechargeable batteries or oil,
which - if handled or disposed of incorrectly - can
pose a potential threat to human health and the environ-
ment. However, these components are required for the
correct operation of the appliance. Appliances marked
by this symbol are not allowed to be disposed of togeth-
er with the household rubbish.
Notes on the content materials (REACH)
Current information on content materials can be found
at: www.kaercher.com/REACH

Accessories and spare parts

Only use original accessories and original spare parts.
They ensure that the appliance will run fault-free and
safely.
Information on accessories and spare parts can be
found at www.kaercher.com.

Scope of delivery

The scope of delivery for the appliance is shown on the
packaging. Check the contents for completeness when
unpacking. If any accessories are missing or in the
22
event of any shipping damage, please notify your deal-
er.
CAUTION
Missing or modified safety devices
Safety devices are provided for your own protection.
Never modify or bypass safety devices.
Chain with a low risk of kickback
A chain with a low risk of kickback reduces the likelihood
of kickback.
The raked teeth (engagement blades) in front of each
saw tooth prevent the saw teeth from engaging too
deeply in the kickback zone, thus reducing the amount
of kickback.
When grinding the chain, there is a danger that this
safety function will be overridden. If the saw perfor-
mance deteriorates, the chain should be replaced for
safety reasons. For spare parts, use only the combina-
tion of guide rail and chain recommended by the manu-
facturer.
Guide rails whose tips have a small radius usually carry
a lower risk of kickback.
Therefore use a guide rail with matching chain for the
task, which is just long enough. Longer guide rails in-
crease the likelihood of loss of control during sawing.
Check the chain tension before each use (see chapter
Checking the chain tension). If the chain tension is not
set correctly, sawing smaller branches (thinner than the
full length of the guide rail) increases the danger of the
chain being thrown off.
If the chain loosens or tears, the chain catcher prevents
the chain from being thrown in the direction of the user.
The integrated bucking spikes can be used as a fulcrum
to give the chain saw stability during a cut.
When sawing, press the device forward until the metal
spikes penetrate the edge of the wood. Subsequently
moving the rear handle up or down in the direction of the
cut reduces the physical strain when working with the
chainsaw.
Chain brakes are used in case of danger to bring the
chain quickly to a standstill.
The chain must come to a standstill immediately when
the hand guard/chain brake lever is pressed in the direc-
tion of the guide rail.
The chain brake cannot prevent kickback, but reduces
the risk of injury if the guide rail hits the user in the event
of a kickback.
The proper function of the chain brake must be checked
before each use of the device (see chapter Checking
the functionality of the chain brake).

Symbols on the device

English
Autogoods "130"

Safety devices

Guide rails
Chain catcher
Bucking spikes
Chain brake
General warning symbol