Water Filter Installation - AQUAPHOR ECO Pro Manual De Instrucciones

.........................................................................................................................................................................................................................................
• A dense hollow fiber membrane retains microparticles from
0.1 microns.
• Efficient removal of organic substances, heavy metals and active
chlorine.
DELIVERY SET
Housing
Connection tube
Connection tube with a cone sleeve insert
Connection unit
Plug (only for Aquaphor ECO Н Pro)
Adaptor for recovery of cartridge Pro Н (only for
Aquaphor ECO Н Pro)
Clean water tap with a set of gaskets and adaptors
Set of replacement filter cartridges
Self-drilling screw
Dowel
Operation manual (product certificate)
Packaging
Types of the ECO Pro water filter
Model ECO Pro
Post-treatment
Function
of drinking water
Replaceable filter Pro 1 – Pro 2 –
cartridges Pro HF
Technical characteristics:
Service life of the
10 000 L
cartridge kit*
Recommended
2.5 l / min
filtering speed
Overall dimensions,
280 × 105 × 375 mm
not more than
Maximum working
0.63 MPa (6 bar)
water pressure
Water temperature +5...+38 °C
Weight, not more
4.0 kg
than
* The service life of the replacement cartridge kit is set for water filtration that
meets the current sanitary standards. If the water being treated does not meet the
current sanitary standards, the service life of the replacement cartridge kit may be
reduced.
** Taking into account the repeated recovery of the replacement Pro H cartridge at
home.
INSTALLATION GUIDE
Installation
1. Clean water tap
2. Water filter
3. Connection unit
4. Sealing strip
5. Rubber O-ring
6. Decorative stand
7. Rubber O-ring
8. Plastic washer
9. Metallic washer
10. Nut
11. Metal bushing
12. Cap nut
13. Tube
14. Locking clips
15. Tube
................................................................................................................................
1 pc. ATTENTION! Only install your filter by a qualified plumber who is
certified to perform the installation in accordance with the law of
1 pc.
your country.
1 pc.
ATTENTION! Measure the water pressure before installation of the
filter. If it exceeds 0.63 MPa, install a pressure reducing valve (not
1 pc.
included in the water filter set).
1 pc.
................................................................................................................................
1 pc.

Water filter installation

1. For installation, you will need: a drill, a 12 mm drill bit, an adjustable
1 pc.
1 pc.
2. Select appropriate location for the clean water faucet (1), water
2 pcs.
2 pcs.
1 pc.
1 pc.
ECO H Pro
Connection unit installation
................................................................................................................................
Post-treatment
and softening
ATTENTION! The end of the pipeline where the connection is done
of drinking water
must be flat.
................................................................................................................................
Pro 1 – Pro H –
Pro HF To prevent damage to the connection unit (3), do not apply significant
force during installation.
No reclamations shall be accepted if mechanical damage is done to
the connection unit (3) during inappropriate installation.
8000 L**
3. Close the cold water supply and discharge pressure by opening
2.0 l / min
4. Install the connection unit (3) between the cold water supply and
Clean water tap installation
5. Drill a 12 mm whole for the clean water tap in the place selected.
................................................................................................................................
ATTENTION! Wetted tubes are inserted to a stop, minimum depth of
15 mm. Make sure that the tube is properly fixed, it must be secured,
it should hold applied force of 80–90 N.
................................................................................................................................
6. Assemble the decorative support (6) and 2 rubber rings (5, 6, 7)
7. Insert the tap end piece (1) into the drilled whole. Put on the plastic
8. Put on the tube with pressed-in brass sleeve (13) the cap nut
9. Connect the tubes supplied with water filter according to the
10. Assemble the water filter (2) according to the cartridges instal-
................................................................................................................................
NOTE. When assembling the ECO H Pro water filter, you do not need
to install the Pro H cartridge at this stage – instead of the Pro H car-
tridge, screw the flushing plug into the middle socket of the collector.
................................................................................................................................
wrench, a screwdriver, a 14 mm tubular wrench.
filter (2) and location for connecting the unit (3) to the water supply
(see the figure). Note that the connecting tubes should be loose
and not bent.
It is recommended to fixate the slack sections of the tubes in
such a way as to avoid damaging or connection errors that may
reduce the flow rate.
The water filter must be placed at a distance or isolated from
any heat sources (kitchen ovens, boilers, hot water supply pipes,
dishwashers or washing machines, etc.).
the tap.
the flexible John Guest tube.
on the tap threaded end piece (1).
washer (8), metallic (stopping) washer (9) and tighten them with
the nut (10).
(12) from the clean water tap set. Connect the tap with the end
of the tube with pressed-in brass sleeve and tighten it with the
fastening nut.
"Water filter installation guide".
lation order (see Section "Cartridges Installation").
EN
5