Rev-A-Shelf 53TM Serie Instrucciones De Montaje

53TM SERIES STAINLESS STEEL TOP MOUNT WASTE CONTAINER
TOOLS REQUIRED: ESTIMATED ASSEMBLY TIME:
20 MIN
WATCH TUTORIALS OF OUR
PRODUCTS BEING INSTALLED
5
64
WWW.REV-A-SHELF.COM/VIDEOS
FIGURE 1
STEP 1
e r n
Place template and mark hole
locations for the left hand slide.
Then attach each lid holder using
(3) #8x1/2" pan head screws
and each slide using (4) #8x5/8"
flathead screws (See Figure 1).
Flip the template and do the same
for the right hand slide.
STEP 4 FIGURE 4
Place the (4) plugs over the
cylindrical screws (See Fig 4).
STEP 6
Align the door brackets to the
slide covers and attach with (2)
1/4-28x1/2" machine screws
and washers (See Fig 7).
STEP 8
Place the door mount covers
over the door mount brackets
(See Fig 9).
1-1/4"
32mm
CARE AND MAINTENANCE:
No.
CLEAN WITH A DAMP CLOTH
1
AND WIPE PARTS DRY
2
3
4
5
6
7
8
9
10
11
11/16"
18-11/16" 12
(475 mm)
(17 mm)
9-5/16"
13
(237 mm)
14
3-1/4"
1-1/4" (32 mm)
(83 mm)
11-5/16"
(287 mm) 1-1/4"
n t u o m p o T
A 1-1/2" (38 mm) (32 mm)
a i n t o c e s t a w
Place the slide covers over the
slides (See Fig 2).
CABINET FLOOR
FIGURE 5
STEP 5
Mark and pre-drill mounting
holes using measurements in
figures 5 and 6. Attach door
mounting brackets using (6)
5/8" (16 mm)
#6x1/2" flathead screws.
BETWEEN HOLES
1-7/8" (48 mm)
2-1/2" (64 mm)
B
+ Door
Overlay
13/16" (20 mm)
+ Door Overlay
FIGURE 7
FIGURE 9
e r n a i
18-11/16"
(475mm)
n t u o m p o
e r n a i n t o c e s t a
11-5/16"
287mm
Parts List
Description Qty
1
Metal Box 1
Lid 1
Slides 2
Slide Covers 2
Lid Holders 2
Door Mounting Brackets 2
7 8
Door Mounting Covers 2
Plugs 4
Waste Bins 2
#8x1/2" Pan Head Screws 12
#8x5/8" Flathead Screws 8
M4x5 Machine Screws 4
#6x1/2" Flathead Screws 6
1/4-28x1/2" Machine Screws 2
FIGURE 2
STEP 2
1)
Make sure that your unit is securely installed into your cabinet. Remove the cabinet door and
hinges to begin to mount your door.
2)
Using the (4) provided screws and nuts, attach the L-Brackets to your slide.
Part Number B
Note: Depending on your particular basket design L-Bracket will mount on either inside or
outside of wire.
53TM-1835GSCDM2-FL 10-7/8" (277 mm)
53TM-1850GSCDM2-FL 14-7/8" (378 mm)
53TM-18GSCDM3-FL 11-1/8" (282 mm)
53TM-24GSCDM4-FL 11-11/16" (297 mm)
STEP 7
Adjust the door using the
adjustment screws (See Fig 8)
until the door is centered and
flush with your frame.
Inside wire shown
3a)
Attach the door brackets to the outside of the L-brackets using the (4) provided screws.
VERTICAL
ADJUSTMENT
STEP 9
Place the lid on the holders
and insert waste bins.
(See Fig 10).
n t o c e s t a w
Top mount
waste container
9-5/16"
Top mount
237mm
waste container
T
w
2 3 4
10 11 12 13
9
STEP 3
Extend the slides and mount
the metal box using the (4)
M4x5 machine screws (See
Fig 3).
FIGURE 6
HOW TO DETERMINE YOUR DOOR OVERLAY:
Measure Opening Height ________
Measure Door Height ________
Height Difference ________
Divide Difference by 2 ________ = Overlay
FIGURE 8
TILT ADJUSTMENT
FIGURE 10
11/16"
17mm
12400 Earl Jones Way
Louisville, KY 40299
rev-a-shelf.com
Customer Service: 800-626-1126
1-1/2"
1-1/4"
38mm
32mm
5 6
14
FIGURE 3
3b)
Cada puerta de gabinete es diferente, pero asegúrese de que el sopor
con la porción gruesa de la puerta del gabinete. Esto asegurará que los torn
dañen su puerta.
Chaque porte d'armoire est différente, mais assurez-vous que le support
la partie épaisse de la porte de l'armoire. Cela permettra d'assurer que le
à travers et endommager votre porte.
3c)
Se proveen espaciadores de plástico si es que los soportes de la puerta
dos para alcanzar la porción gruesa de la puerta.
Des espaceurs en plastique sont fournis si les supports de porte doivent êt
pour atteindre la partie épaisse de la porte.
4)
Aplique cinta de doble lado a los soportes de la puerta. Sujete la puerta
soportes mientras trata de mantener la puerta a nivel. No se preocupe si la p
poco, esto puede ser ajustado. La cinta de doble lado sujetara la puerta en s
atornilla los soportes a la puerta del gabinete.
Mettez du ruban adhésif double sur les supports de porte. Fixez la porte d
supports tout en essayant de maintenir la porte à niveau. Ne vous inquiét
tout à fait à niveau, tout cela peut être ajusté. Le ruban adhésif double tie
pendant que vous vissez les supports sur la porte de l'armoire.
T-53TM-0619