Kinderkraft B-TOUR Manual De Usuario página 28

WARNING! THE PRAM BODY CAN ONLY BE MOUNTED FACING
BACKWARDS (the child faces the person pushing the buggy).
IV ASSEMBLY/DISASSEMBLY OF THE SAFETY BAR, SHADE, COVER FOR LEGS AND CUP HOLDER The safety bar (6) can be
used in both the carrycot and buggy versions. Slide ends of the safety bar into the adequate holes until you hear a lock
click on both sides (Fig. K). The safety bar can be partially or fully detached from the frame by pressing a button on its
side/sides.
NOTE! INSTALL THE CANOPY BEFORE USING THE BUGGY
Start the installation of the shade (9) by sliding plastic fasteners over the rails on the carrycot/seat frame (Fig. L). Correct
fixing is signaled with a gentle click. Finally, secure the shade with Velcro fasteners and snap fasteners – fastening them to
the carrycot/seat. In order to disassemble the shade, press buttons (Fig. M) and remove the fasteners from guides.
Start the assembly of the leg cover (10) by inserting the cover and then fastening both sides of the cover with sheathing
using snap fasteners – as shown in Figures N-I. Put the button through the loop on the sheathing and then wrap the cover
on both sides of the safety bar and secure with buttons (Figures N-II and N-III). The cup holder (16) can be mounted on the
right side of the stroller – on a spindle (Fig. O).
V TRANSFORMING A PRAM BODY INTO A SEAT In order to transform the carrycot into the seat, first connect ends of the
removed straps behind the backrest under the seat and under the footrest (Fig. P). After the correct fastening of belts, the
seat should look as shown in Figure Q (the method for adjusting the seat angle is described in chapter X). The should/lap
straps and the crotch strap should be fitted (assembly/disassembly of the straps is described in chapter XI).
VI ASSEMBLY OF THE BAG, MOSQUITO NET AND RAIN COVER
The stroller's set includes: a bag (12) with a changing mat (13), fabric hangers (14), a rain cover (17) and a mosquito net
(18). Hang the bag on the parent handle with the use of hangers (pulling the straps through metal loops) and secure it with
Velcro fastener (Fig. R).
Install and secure the mosquito net by inserting buttons through loops (Fig. S). Place the rain cover over the stroller and
secure it with Velcro fasteners to the back and side of the backrest (Fig. T).
VII ASSEMBLY/DISASSEMBLY OF THE CAR SEAT The attached adapters (11) are compatible with car seats: Kinderkraft®,
Kiddy®, Maxi Cosi®, Cybex®, BeSafe®, Nuna® and they fit, among others, for models: Kinderkraft MINK, Kiddy Evoluna I-
Size 2, Evolution Pro 2, Cybex Aton, Aton 2, Aton Q, Maxi Cosi Mico, Mico AP, Mico NXT, Mico Max 30, Citi, Cabrio,
CabrioFix, BeSafe iZi Go, iZi Go Modular, Nuna Pipa.
Slide adapters into the holes in the frame until you hear a locking sound (Fig. U). The adapters should be slightly tilted
towards the parent. Slide the seat onto adapters and make sure that it is properly secured. The stroller along with a seat
is shown in Figure V. To remove the adapters from the stroller, press lock buttons on each of adapters (Fig. W).
WARNING! The car seat must be always placed on the frame
back to the direction of travel (the child should face the person
pushing the buggy).
VIII USING THE BRAKE The stroller is equipped with a foot parking brake on the rear axle. Press the brake pedal downwards
to activate the brake. To unlock, lift the pedal up (Fig. X).
IX DISASSEMBLY OF THE STROLLER In order to disassemble the carrycot/seat from the frame, press buttons on both
sides (placing your fingers on the bottom of buttons as shown in the picture (Fig. Y)) and lift the carrycot/seat. After
removing the carrycot/seat or the car seat, rotate the cup holder to the side (Fig. Z), push the button and simultaneously
pull levers on both sides of the frame. Finally, push the parent handle down (Fig. Z). Correctly assembled frame should
be secured with the lock on the side (Fig. AA) Folded stroller can be carried by the strap mounted under the seat of the
stroller. If necessary, front (Fig. BB) and rear (Fig. CC) wheels can be detached from the frame by pressing buttons. It is
possible to minimize dimensions of the stroller after folding. To do this, press buttons on both sides of the frame – as
shown in the figure (Fig. DD).
The carrycot/seat sheathing can be removed for washing. In the first step, remove the shade (see point IV). Then, unfasten
two zippers, remove side straps from the sheathing (located in the area of child's legs) and unfasten snaps under the
carrycot/seat. In the next step, remove shoulder/lap strap and the crotch strap, as well as remove the s tiffening insert
from the seat.
X ADJUSTMENT OF THE STROLLER Front wheels of the stroller can be locked for driving straight ahead. Enable this mode
by lowering the lock sliders (Fig. EE). Pull sliders upwards to unlock front wheels. The shade can be enlarged by opening
the zipper on the outer side of the sheathing (Fig. FF).
28