¦
Listening through a Receiver
You can listen to sound through a receiver (i.e Home Theatre) instead of the TV speaker.
1. Select Receiver and set to On.
2. Press the
button to exit.
EXIT
✎
If your receiver supports audio only, it may not appear in the device list.
✎
The receiver will work when you have properly connected the optical in jack of the receiver to the
OUT (OPTICAL)
jack of the TV.
✎
When the receiver (i.e Home Theatre) is set to On, you can hear sound output from the TV's Optical jack. When the
TV is displaying a DTV (aerial) signal, the TV will send out 5.1 channel sound to the receiver. When the source is a
digital component such as a DVD and is connected to the TV via HDMI, only 2 channel sound will be heard from
the receiver.
✎
NOTE
x
You can only control Anynet
x
The TV remote control may not work under certain conditions. If this occurs, reselect the Anynet
x
The Anynet
functions do not operate with other manufacturers' products.
+
Troubleshooting for Anynet
¦
Problem
Possible Solution
Anynet
does not work.
+
I want to start Anynet
.
+
I want to exit Anynet
.
+
The message "Connecting to
Anynet
device..." appears on the
+
screen.
The Anynet
device does not play.
+
The connected device is not
displayed.
The TV programme cannot be
recorded.
The TV sound is not output
through the receiver.
All manuals and user guides at all-guides.com
devices using the TV remote control, not the buttons on the TV.
+
+
•
Check if the device is an Anynet
device. The Anynet
+
•
Connect only one receiver (home theatre).
•
Check if the Anynet
device power cord is properly connected.
+
•
Check the Anynet
device's Video/Audio/HDMI Cable connections.
+
•
Check whether Anynet
(HDMI-CEC) is set to On in the Anynet
+
•
Check whether the TV remote control is in TV mode.
•
Check whether it is Anynet
exclusive remote control.
+
•
Anynet
does not work in certain situations. (Searching channels, operating Media Play or Plug & Play (Initial
+
setup), etc.)
•
When connecting or removing the HDMI cable, please make sure to search devices again or turn your TV off
and on again.
•
Check if the Anynet
Function of Anynet
+
•
Check if the Anynet
device is properly connected to the TV and check if the Anynet
+
in the Anynet
Setup menu.
+
•
Press the
TOOLS
button to display the Anynet
•
Select
View TV in the Anynet
menu.
+
•
Press the
SOURCE
button on the TV remote control and select a device other than Anynet
•
Press
P
>/<, PRE-CH, and
FAV.CH
when a tuner-embedded Anynet
device is not connected.)
+
•
You cannot use the remote control when you are configuring Anynet
•
Use the remote control when the Anynet
•
You cannot use the play function when
•
Check whether or not the device supports Anynet
•
Check whether or not the HDMI Cable is properly connected.
•
Check whether
Anynet
(HDMI-CEC) is set to On in the Anynet
+
•
Search Anynet
devices again.
+
•
You can connect an Anynet
device using the HDMI Cable only. Some HDMI cables may not support Anynet
+
functions.
•
If it is terminated by an abnormal situation such as disconnecting the HDMI cable or power cord or a power
failure, please repeat the device scan.
•
Check whether the antenna jack on the recording device is properly connected.
•
Connect the optical cable between TV and the receiver.
system supports Anynet
+
+
setup menu.
+
device is set on.
+
menu and select a menu you want.
+
to change the TV mode. (Note that the channel button operates only
or switching to a view mode.
+
setting or switching to view mode is complete.
+
Plug & Play (Initial setup) is in progress.
functions.
+
setup menu.
+
DIGITAL AUDIO
device.
+
devices only.
(HDMI-CEC) is set to On
+
devices.
+
+
31
English