Publicidad
Idiomas disponibles
Idiomas disponibles
Receiver Setup for New Receivers, Continued
3
The satellite will begin searching and find the needed satellites (see fig. 3).
4
The satellite will return to step 2 and begin updating the receiver (see fig. 1). Once completed, the receiver will reboot.
5
After rebooting, the Mobile Setup screen must be completed again. After the update, regardless of manufacture date of the
receiver, the Mobile Setup screen will be figure 2B. Select the number of receivers, the arc (if one receiver was selected), and the
state that you are currently in, and press "Scan" to begin the search routine.
6
The satellite will begin searching and will locate the desired satellites (see fig. 3).
7
After re-acquiring, the receiver will return to the Installation Wizard and complete step 2.
8
During step 3 of the Installation Wizard, set the resolution output to match the TV being used. Follow the on-screen instructions to
complete this step.
9
During step 4 of the Installation Wizard, the receiver will test for an Ethernet or phone connection. In a mobile application, typically
a phone/Ethernet is not connected. An error message will be displayed (see fig. 4), and you will need to re-test. After the second
attempt, the Installation Wizard will move to the next step.
10
During step 5 of the Installation Wizard, the receiver will need to be activated. To activate the receiver, call Winegard Company at
1-866-609-9374.
11
After the receiver has been activated, the receiver will begin downloading the Electronic Programming Guide (see fig. 5). Once the
download is complete, you can start watching TV.
Figure 3
Figure 4
Receiver Setup for Currently Active or Previously Used Receivers
If the receiver you will be using with the Pathway X2 antenna is an older receiver that has not been used in several years, you may
need to connect the receiver to a home satellite dish to be updated before proceeding with the mobile setup.
1
After the receiver has been powered on, the receiver will enter the Mobile Setup menu.
2
Depending on the software version in your receiver, the setup screen may differ between figure 6A and 6B. Fill in the required
information, and then select "Scan" to begin the search routine.
3
The satellite will begin searching and will locate the desired satellites (see fig. 7).
4
After the satellites have been acquired, the Electronic Programming Guide will download (see fig. 8).
5
If figure 6A was the setup screen seen in step 2, the receiver should be updated to the latest software for full functionality with the
Pathway X2 antenna. To allow the software to update, leave the satellite on signal, and press the Power button on the remote or
front panel of the receiver; this will put the receiver in Standby mode (see fig. 9). Do not unplug the receiver at this time.
6
After being in Standby mode for a few minutes, the software will automatically begin to update (see fig. 10). Upon completion of
the update, the receiver will reboot. Return to step 1 to re-acquire satellites and complete setup.
Figure 6A
Figure 6B
3
Receiver setup instructions are accurate at time of printing and may change without notice.
All manuals and user guides at all-guides.com
1
2
3
Figure 5
Figure 7
Receiver Setup for Currently Active or Previously Used Receivers, Continued
Figure 8
Figure 9
Receiver Setup for a Secondary Receiver
After completing setup on the main receiver, power on the secondary receiver. If using a new receiver, you will be guided through
the setup by the Installation Wizard; follow the on-screen steps to complete setup. If using a receiver that is currently active or has
been used previously, you will need to complete setup by doing a Check Switch test. To access the receiver menu for running a
Check Switch test, follow the steps under "Accessing the Receiver Menu."
Accessing the Receiver Menu
If you need to access the receiver menu after initial setup, follow the steps below to reach the receiver menu.
Press "Menu" on your remote. Select option 6, "System Setup."
Select option 1, "Installation" (see fig. 11). Then, select option 1, "Point Dish" (see fig. 12).
Select "Check Switch" (see fig. 13), and complete the Check Switch test.
Figure 11
Figure 12
Cleaning &
Transporting the
Antenna
Maintenance
Before transporting the antenna, return
The Pathway X2 antenna is designed
the antenna to the stowed position. To
to be maintenance free. However, it is
stow the antenna, disconnect the coax
a good idea to clean the reflector cover
cables from the main and secondary
from time to time. Clean the reflector
ports, and rotate the antenna until the
cover with a soft cloth, water, and dish
elevation arrow aligns with "STOW."
soap to avoid scratching the cover.
Disclaimer: Although every effort has been made to ensure that the information in this
manual is correct and complete, no company shall be held liable for any errors or omissions
in this manual. Information provided in this manual was accurate at time of printing. If
the antenna does not function as expected, please contact Winegard Company at help@
winegard.com or 1-800-788-4417, or visit our website at www.winegard.com.
Figure 10
Figure 13
Tripod Mount
Accessory
Model TR-1518 tripod mount (sold
separately) is available as an accessory
for the Pathway X2 antenna. The tripod
mount has adjustable height and
leveling settings of 14.5"–22" and quickly
disassembles for compact storage.
4
Publicidad
