Resetting The Unit - Onkyo HT-RC660 Manual Básico

Ocultar thumbs Ver también para HT-RC660:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

Troubleshooting
Before starting the procedure
Problems may be solved by simply turning the power
on/off or disconnecting/connecting the power cord,
which is easier than working on the connection,
setting and operating procedure. Try the simple
measures on both the unit and the connected
device. If the problem is that the video or audio is not
output or the HDMI linked operation does not work,
disconnecting/connecting the HDMI cable may solve
it. When reconnecting, be careful not to wind the
HDMI cable since if wound the HDMI cable may not fit
well. After reconnecting, turn off and on the unit and
the connected device.
The AV receiver turns off unexpectedly.
The AV receiver will automatically enter standby mode
when Auto Standby is set and launched.
There's no sound, or it's very quiet.
A wrong input selector button has been selected. Select
a correct input for the player. Also check that muting is
not on.
Not all listening modes use all speakers.
There's no picture.
A wrong input selector button has been selected.
Video is not displayed if the listening mode is Pure Audio.
(European model)
To display video from the connected player on the TV
screen while the unit is in standby, you need to enable
HDMI Through function.
When the TV image is blurry or unclear, power cord or
connection cables of the unit may have interfered. In
that case, keep distance between TV antenna cable and
cables of the unit.
18
All manuals and user guides at all-guides.com
HDMI control does not function correctly.
Set the CEC link function of the unit to on. It is also
necessary to make the HDMI linked system setting on
the TV. See the TV's instruction manual for details.
The remote controller does not work.
Be sure to press RCV first before operating the unit with
the remote controller.
There is no sound for multi-zone function.
With multi-zone function, sound is output only when the
signal input source is an external component connected
to the analog audio input jacks of the unit, "NET", "USB"
or "BLUETOOTH". Multi-zone playback is not possible if
the player and the unit are connected via HDMI cable or
digital cable. Connect the RCA audio output jacks of the
player and the analog audio input jacks of the unit with
analog audio cable. Also analog audio output setting may
be necessary on the player.
Cannot access to network.
Try plugging/unplugging the unit or the wireless LAN
router or check their power-on status. This will work well
in many cases.
If the desired wireless LAN router is not in the access
point list, it may be set to hide SSID or the ANY
connection may be off. Change the setting and try again.
Bluetooth
Try plugging/unplugging the unit and the Bluetooth-
enabled player. After that, check that the Bluetooth
function is enabled on the Bluetooth-enabled device and
the connection with the unit has been established.

Resetting the unit

Resetting the unit to the status at the time of shipment may
solve the problem. If the measures above do not solve the
problem, reset the unit with the following procedure. If you
reset the unit status, your preferences will be reset to the
defaults. Note them down before starting reset.
How to reset:
1.
While holding down CBL/SAT on the main unit (note
that step 2 must be performed with this button
pressed down)
2.
Press zON/STANDBY on the main unit ("Clear"
appears on the display and the unit returns to
standby)
2.
1.
Press
While holding
zON/STANDBY.
down CBL/SAT,
How to reset the remote controller:
1.
While holding down RCV on the remote controller,
press HOME until the remote indicator lights (about
3 seconds)
2.
Within 30 seconds, press RCV again
RCV
C l e a r
Remote
indicator
HOME

Publicidad

Tabla de contenido
loading

Tabla de contenido