DeWalt DCH832 Manual Del Usuario página 35

To Remove the Battery Pack from the Tool
1. Press the battery release button
battery pack out of the tool handle.
2. Insert battery pack into the charger as described in the
charger section of this manual.
Fuel Gauge Battery Packs (Fig. B)
Some D WALTD WALT battery packs include a fuel gauge
e e
which consists of three green LED lights that indicate the level
of charge remaining in the battery pack.
To actuate the fuel gauge, press and hold the fuel gauge
button 16 . A combination of the three green LED lights will
illuminate designating the level of charge left. When the level
of charge in the battery is below the usable limit, the fuel gauge
will not illuminate and the battery will need to be recharged.
nOTE: The fuel gauge is only an indication of the charge left on
the battery pack. It does not indicate tool functionality and is
subject to variation based on product components, temperature
and end‑user application.
Bail/Loop Style Auxiliary Handle (Fig. C)

WARNING: To reduce the risk of personal injury, ALWAYS
operate the tool with the bail/loop style auxiliary handle
properly installed. Failure to do so may result in the bail/
loop style auxiliary handle slipping during tool operation
and subsequent loss of control. Hold tool with both hands
to maximize control.
The bail/loop style auxiliary handle
the gear case and may be rotated 360˚ to permit right‑ or
left‑hand use.
Mounting the Bail/Loop Style Auxiliary Handle
(Fig. C)
1. Widen the ring opening
handle 2 by rotating the screw for handle mounting
counter clockwise.
2. Slide the assembly onto the nose of the tool through
the ring opening 13 and onto the chisel position index
collar 3 , past the chisel holder and sleeve.
3. Rotate the bail/loop style auxiliary handle to the
desired position.
4. Lock the bail/loop style auxiliary handle in place by securely
tightening the screw for handle mounting
clockwise so that the assembly will not rotate.
Bit and Bit Holder

WARNING: Burn Hazard. ALWAYS wear gloves when
changing bits. Accessible metal parts on the tool and bits
may get extremely hot during operation. Small bits of
broken material may damage bare hands.
Inserting and Removing SDS max® Accessories
(Fig. D)
This machine uses SDS max® chisels (refer to the inset in
Figure D for a cross‑section of an SDS max® bit shank).
1. Clean the bit shank.

WARNING: Do not apply lubricant to the machine.
9 and firmly pull the
clamps to the front of
2
13 of the bail/loop style auxiliary
14 rotating it
2. Pull back the locking sleeve
3. Release the locking sleeve and turn the bit slightly until the
sleeve snaps into position.
4. Pull on the bit to check if it is properly locked. The
hammering function requires the bit to be able to move
axially several centimetres when locked in the bit holder.
5. To remove a chisel pull back the bit holder locking sleeve/
collar 7 and pull the chisel out of the chisel holder
OPERATION
Instructions for Use

WARNING: Always observe the safety instructions and
applicable regulations.

WARNING: To reduce the risk of serious personal
injury, turn tool off and disconnect battery pack
before making any adjustments or removing/
installing attachments or accessories. An accidental
start-up can cause injury.
Proper Hand Position (Fig. A, E)

WARNING: To reduce the risk of serious personal injury,
ALWAYS use proper hand position as shown.

WARNING: To reduce the risk of serious personal
injury, ALWAYS hold securely in anticipation of a
sudden reaction.
Proper hand position requires one hand on the bail/loop style
auxiliary handle
Operation Modes (Fig. A)

WARNING: Do not select the operating mode when the
tool is running.
Your tool is equipped with a mode selector dial
mode appropriate to desired operation.
14
symbol
hammering only Light chipping
Bit adjustment Chisel bit position adjustment
To Select an Operating Mode
• Rotate the mode selector dial so that the arrow points to the
symbol corresponding for the desired mode.
nOTE: The arrow on the mode selector dial
at a mode symbol at all times. There are no operable positions
in between.
Indexing the Chisel Position (Fig. A)
The DCH832 can be indexed and locked into
18 different positions.
The DCH892 can be indexed and locked into
24 different positions.
1. Rotate the mode selector switch
the position.
2. Rotate the chisel to the desired position.
7 and insert the bit shank.
2 with the other hand on the main handle
Mode application
until it points towards
4
EngLIsh
6 .
5 .
to select the
4
4 must be pointing
33