Safety Instructions - DeWalt DW625E Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27
E N G L I S H

Safety instructions

When using Power Tools, always observe the
safety regulations applicable in your country to
reduce the risk of fire, electric shock and personal
injury. Read the following safety instructions
before attempting to operate this product.
Keep these instructions in a safe place!
General
1 Keep work area clean
Cluttered areas and benches can cause accidents.
2 Consider work area environment
Do not expose Power Tools to humidity.
Keep work area well lit. Do not use Power Tools
in the presence of inflammable liquids or gases.
3 Guard against electric shock
Prevent body contact with earthed surfaces
(e.g. pipes, radiators, cookers and refrigerators).
For use under extreme conditions (e.g. high
humidity, when metal swarf is being produced,
etc.) electric safety can be improved by inserting
an isolating transformer or a (FI) earth-leakage
circuit-breaker.
4 Keep children away
Do not let children come into contact with the
tool or extension cord. Supervision is required
for those under 16 years of age.
5 Extension cords for outdoor use
When the tool is used outdoors, always use
extension cords intended for outdoor use and
marked accordingly.
6 Store idle tools
When not in use, Power Tools must be stored in
a dry place and locked up securely, out of reach
of children.
7 Dress properly
Do not wear loose clothing or jewellery.
They can be caught in moving parts.
Preferably wear rubber gloves and non-slip
footwear when working outdoors. Wear protective
hair covering to keep long hair out of the way.
8 Wear safety goggles
Also use a face or dust mask in case the
operations produce dust or flying particles.
9 Beware of maximum sound pressure
Take appropriate measures for the protection
of hearing if the sound pressure of 85 dB(A) is
exceeded.
en - 2
All manuals and user guides at all-guides.com
10 Secure workpiece
11 Do not overreach
12 Avoid unintentional starting
13 Stay alert
14 Disconnect tool
15 Remove adjusting keys and wrenches
16 Use appropriate tool
17 Do not abuse cord
18 Maintain tools with care
19 Check for damaged parts
Use clamps or a vice to hold the workpiece. It is
safer and it frees both hands to operate the tool.
Keep proper footing and balance at all times.
Do not carry the plugged-in tool with a finger on
the switch. Be sure that the switch is released
when plugging in.
Watch what you are doing. Use common sense.
Do not operate the tool when you are tired.
Shut off power and wait for the tool to come to a
complete standstill before leaving it unattended.
Unplug the tool when not in use, before servicing
or changing accessories.
Always check that adjusting keys and wrenches are
removed from the tool before operating the tool.
The intended use is laid down in this instruction
manual. Do not force small tools or attachments
to do the job of a heavy-duty tool. The tool will
do the job better and safer at the rate for which
it was intended.
Warning! The use of any accessory or
attachment or performance of any operation with
this tool, other than those recommended in this
instruction manual may present a risk of personal
injury.
Never carry the tool by its cord or pull it to
disconnect from the socket. Keep the cord away
from heat, oil and sharp edges.
Keep the tools in good condition and clean for
better and safer performance. Follow the
instructions for maintenance and changing
accessories. Inspect the tool cords at regular
intervals and, if damaged, have them repaired
by an authorized D
WALT repair agent.
E
Inspect the extension cords periodically and
replace them if damaged. Keep all controls dry,
clean and free from oil and grease.
Before using the tool, carefully check it for
damage to ensure that it will operate properly
and perform its intended function.
16

Publicidad

Tabla de contenido
loading

Tabla de contenido