Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
EN
PREAMPLIFIER
FS-2601E
BREAKER
PROT
FS-2601
TEMP
POWER CONSUMPTION: 1,000 W
CLIP
CAUTION: SHOCK HAZARD - DO NOT OPEN
RISK OF FIRE-REPLACE FUSE AS MARKED
~ 230 V AC. 60 Hz FUSE: 6 A
SIGNAL
FS-2601E
BREAKER
FS-2601
1
2
3
4
5 6
7 8
POWER CONSUMPTION: 1,000 W
CAUTION: SHOCK HAZARD - DO NOT OPEN
RISK OF FIRE-REPLACE FUSE AS MARKED
~ 230 V AC. 60 Hz FUSE: 6 A
INSTRUCTIONS FOR USE
2
ON AND OFF
Before switching the power amplifier on, check that the output volume control is at its minimum. Switch on
the rest of the audio system, and lastly switch on the power amp and adjust the output volume.
OUTPUT
COM
4
8
To switch the audio system off, turn the power amp volume to its minimum and switch it off. Then switch
off the rest of the audio system.
PROTECTION
INPUT
PUSH
The power amp has 3 types of protection: temperature, short circuit in the loudspeaker outputs and overload.
When one type of protection is activated, a LED indicator lights up on the front panel and the audio output is
cut. In this case, switch the power amp off, check the cause of the protection activation, let the equipment
rest for a while and switch it on again.
5
1
AUTOMATIC COMPRESSION FUNCTION
To avoid output distorsion and the amp overheating, the compression function automatically decreases the
input signal level when it is very high or when the temperature of the amplifier is very high.
BREAKER
FS-2601
POWER AMPLIFIER
4 x 90 W RMS
POWER CONSUMPTION: 1,000 W
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: SHOCK HAZARD - DO NOT OPEN
RISK OF FIRE-REPLACE FUSE AS MARKED
RESETTABLE FUSE
~ 230 V AC. 60 Hz FUSE: 6 A
The power supply source is made up of advanced components that absorb the current peaks and eliminate
4
fluctuations caused when the power amp is turned on. Furthermore, the amplifier is equipped with a 6 A
resettable BREAKER fuse on the rear panel.
If the fuse blows, due to a surge or excessive consumption, switch the amplifier off, check the cause of the
blown fuse, let the equipment rest for a while and then reset the BREAKER fuse by pressing it.
100 V
OUTPUT
COM
4
8
70 V
100 V
MASTER
TREBLE
POWER AMPLIFIER
4 x 90 W RMS
INPUT
LINK
PUSH
PUSH
MID
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
BASS
OUTPUT
COM
4
8
70 V
100 V
POWER AMPLIFIER
4 x 90 W RMS
9
10
INPUT
LINK
PUSH
PUSH
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Example of connection of a preamplifier and two amplifiers in cascade
with loudspeakers connected in high impedance 100 V line
PROT
TEMP
3
CLIP
SIGNAL
70 V
100 V
1
2
3
4
5 6
7 8
LINK
PUSH
6
2
OUTPUT
COM
4
BREAKER
INPUT
PUSH
5
100 V
POWER AMPLIFIER FS-2601E
11 12
MASTER
TREBLE
MID
BASS
9
10
7
3
8
70 V
100 V
PROT
TEMP
LINK
PUSH
LED protection indicators
6
BREAKER
100 V
100 V
LED protection indicators
- 4 -
TEMP
100 V
100 V
100 V
100 V
100 V
100 V
POWER AMPLIFIER FS-2601E
11 12
7
PROT
TEMP
Publicidad
Tabla de contenido
