Stanley STEL701 Manual De Instrucciones página 19

or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
STANLEY Service Center or an equally qualified
person in order to avoid damage or injury. If the
power cord is replaced by an equally qualified
person, but not authorized by STANLEY,
the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz .......
Read
Instructions
W ........
Manual
min .....
Use Eye
Protection
Use Ear
Protection
V ........ Volts
n .......
0
A ........ Amperes
Hertz
...... Class II
Watts
....
minutes
..... Alternating
....
Current
..... Direct
.../min..
Current
No-Load
Speed
f Always wear proper eye and respiratory protection.
f Before using, inspect the cutting wheel for cracks
or flaws. If such a crack or flaw is evident, discard
the wheel. The wheel should also be inspected
whenever you think the tool may have been
dropped. Flaws may cause wheel breakage.
f When starting the tool with a new or replacement
wheel or if you are unsure of the condition of the
wheel, hold the tool in a well protected area and
let it run for one minute. If the wheel has an
undetected crack or flaw, it should burst in less than
one minute. Never start the tool with a person in line
with the wheel. This includes the operator.
f In operation, avoid bouncing the wheel or giving it
rough treatment. If this occurs, stop the tool and
inspect the wheel for cracks or flaws.
f Clean your chop saw periodically following the
procedure in this manual.
f Do not remove wheel guards or base.
f Always use the vise or special fixture to clamp
work securely. Other aids such as spring, bar, or
C-clamps may be appropriate for certain sizes and
shapes of workpiece. Use care in selecting and
placing these clamps and make a dry run before
making a cut.
f Use only 14" type 1 wheels rated at 4100 rpm or higher.
f Allow cut off parts to cool before handling.
f Do not attempt to cut wood or plastic with this tool.
f Never cut magnesium with this tool.
f Use chop saw in a well-ventilated area.
f Turn chop saw off before removing any pieces from
the base.
f Do not cut electrically live material.
f Do not use circular saw blades or any other
toothed blades with this tool. Serious injury may
result.
f Do not operate this tool near flammable liquids,
gases or dust. Sparks or hot chips from cutting or
arcing motor brushes may ignite combustible materials.
Construction
f Do not use the side of the abrasive wheel as a
Earthing
Terminal
deburring grinder. This will substantially weaken the
Safety Alert
wheel creating an unsafe condition. The wheel may
Symbol
come apart.
Revolutions
or Recipro-
cation per
Caution! Wear appropriate hearing protection
minute
during use. Under some conditions and duration of use,
noise from this product may contribute to hearing loss.
Caution! Spark deflector will get hot. Avoid touching
or adjusting while hot. Keep cordset and materials away
from spark deflector.
ENGLISH • 19
ADDITIONAL SAFETY RULES
FOR CHOP SAWS