Descargar Imprimir esta página
Ocultar thumbs Ver también para WT-1610:

Publicidad

Enlaces rápidos

Subject:
Belt Tension Tool Kit
Kit:
91176
Model(s):
WT-1610, WT-1610T, WT-1610HSP
To adjust the tension of the belt, follow these steps:
1. Shut off the engine. Disconnect the spark plug wire.
2. Remove front cover (1).
3. Before loosening the spindle housing or removing the
old belt, set the belt tensioning tool in the four holes
(4) behind the spindle housing. Engage handle (7) to
extend bolt (8).
4. Adjust bolt (8) so that it touches the flat spot on the
spindle casting. Disengage handle (7) and remove the
tool.
5. Loosen the four spindle bolts (2) fastening the spindle
housing to the trimmer bottom frame. This will allow
the spindle housing with the attached trimmer pulley to
move freely and relax the belt tension.
6. WT-1610: Remove the two screws (3) on the sides
of the body at the back of the machine. Push up on
the handle bar. The body will pivot near the front of
the engine, opening the back, and exposing the belt.
Place a small block of wood in the opening to keep from
closing.
WT-1610T: Remove the four screws (3) on the sides of
the body below the engine. Remove plate (4) to expose
the belt.
WT-1610HSP: Remove the four bolts (3) and washers
(4) attaching transmission cover (5) to transmission
mount bracket (6). Remove cover (5) to expose the
transmission and gain access to the belts.
7. Remove the worn or broken belt.
8. Install the new belt from the front to the back. Feed the
belt above the front trimmer pulley and below the rear
pulley. Ensure the belt is seated on the spindle pulley
and inside of the belt guides prior to installing on the
crank shaft pulley.
9. WT-1610: Remove the block of wood. Close the trimmer
body and install the two screws (3).
WT-1610T: Install bottom plate (4) and secure with the
four screws (3).
WT-1610HSP: Install transmission cover (5) and
secure with the four screws (3) and washers (4).
10. Adjust the tensioning tool bolt (8), from the previously
set reference point in step 4, as described below.
New belt
In 1 turn.
Old belt
Out 2/3 turn
99922205601
Belt Tension Tool Kit 91176
WARNING
Before inspecting or servicing any part of this machine,
shut off power source, disconnect spark plug wire from
spark plug and make sure all moving parts have come to
a complete stop.
11. With handle (7) disengaged, place the belt tensioning
tool in the four holes behind the spindle housing. Engage
handle (7) to the extend bolt and apply tension.
12. Tighten the four spindle bolts (2). Disengage the belt
tension tool and remove it from the unit.
13. Replace front cover.
NOTE
A belt that is too tight will damage spindle bearings
and belt.
A belt that is too loose will slip, cause premature
failure and poor performance
The engine should be placed under load while in thick
grass, if not the belt may be slipping
©2020 ECHO Incorporated. All Rights Reserved.
- 1 -
©2020 ECHO Incorporated. Tous Les Droits Sont Réservés.
©2020 ECHO Incorporated. Todos Los Derechos Reservados.
INSTRUCTION SHEET
WT-1610 Model

Publicidad

loading

Resumen de contenidos para Echo WT-1610

  • Página 1 ● The engine should be placed under load while in thick 6. WT-1610: Remove the two screws (3) on the sides grass, if not the belt may be slipping of the body at the back of the machine. Push up on the handle bar.
  • Página 2: Instruction Sheet

    INSTRUCTION SHEET Belt Tension Tool Kit 91176 WT-1610T Model WT-1610HSP Model - 2 -...
  • Página 3 INSTRUCTION SHEET Belt Tension Tool Kit 91176 Subject: Belt Tension Tool Kit Kit: 91176 Model(s): WT-1610, WT-1610T, WT-1610HSP WT-1610 Model BELT TENSION TOOL KIT, PN-91176 ITEM PART NUMBER DESCRIPTION YH434000000 BOLT, 1/4-20 X 3/4 GR5 HEX HD YH434000100 BOLT, 5/16 NCX 2-3/4 GR5 HCPS ZP...
  • Página 4 6. WT-1610: Retire los dos tornillos (3) a los lados del cuerpo en la parte posterior de la máquina. Empuje hacia arriba el manillar.
  • Página 5 HOJA DE INSTRUCCIONES JUEGO DE HERRAMIENTAS DE TENSIÓN DE CORREA 91176 WT-1610T Modelo WT-1610HSP Modelo - 5 -...
  • Página 6 HOJA DE INSTRUCCIONES JUEGO DE HERRAMIENTAS DE TENSIÓN DE CORREA 91176 Modelo WT-1610 JUEGO DE HERRAMIENTAS PARA TENSIÓN DE CORREA, PN-91176 ARTICULO NÚMERO DE PARTE DESCRIPCIÓN CANTIDAD YH434000000 PERNO, 1 / 4-20 X 3/4 GR5 HEX HD YH434000100 PERNO, 5/16 NCX 2-3 / 4 GR5 HCPS ZP...
  • Página 7 9. WT-1610: Retirez le bloc de bois. Fermez le corps de la tondeuse et installez deux vis (3). WT-1610T: Installez la plaque inférieure (4) et fixez-la avec quatre vis (3).
  • Página 8 FEUILLE D’INSTRUCTION KIT D'OUTILS DE TENSION DE COURROIE 91176 Modèle WT-1610HSP Modèle WT-1610T - 8 -...
  • Página 9 FEUILLE D’INSTRUCTION KIT D'OUTILS DE TENSION DE COURROIE 91176 Modèle WT-1610 KIT DE L'OUTIL DE TENSIONNEMENT DE COURROIE, RÉF 74678-00 ARTICLE Nº DE RÉFÉRENCE DESCRIPTION QTÉ YH434000000 BOULON, 1/4-20 X 3/4 GR5 HEX HD YH434000100 BOULON, 5/16-18 X 2-3/4 GR5 HCPS YH449000030 ÉCROU, 1/4-20 NYLOCK COLLERETTE...

Este manual también es adecuado para:

Wt-1610tWt-1610hsp91176