Electrical Connections; Troubleshooting - Dri-Eaz Ace Manual Del Propietário

ELECTRICAL CONNECTIONS

Ace TurboDryers are designed to operate on a 230V/50 Hz
electrical connection. Make sure that the electrical outlet is
grounded and that all safety precautions are taken.
MAINTENANCE
Always turn off the power before performing maintenance pro-
cedures. All the service procedures below are to be executed
with the unit unplugged. Perform before each use or as
needed.
INSPECT ELECTRICAL SYSTEM: Inspect the electrical cord
for damage at regular intervals. Periodically, remove the hous-
ing and inspect internal wiring for bare wires, insecure fasten-
ers, and discoloration. Remove and repair any damaged wiring
as needed. Failure to do so may lead to electrical shock or a
fire hazard.
CLEAN GRILLS: Clean off any accumulated lint or other mate-
rials from the protective grill cover. A buildup will reduce the
airflow and may cause the motor to overheat and become a
SPECIFICATIONS
Model
Operating Positions
Power, 230 Volts
Actual CFM
RPM
Static Pressure
Motor Rating
Motor Speeds
Thermal Protection
Switch
Fan Blade
Height, Width, Length
Use Weight
Ship Weight
Stackable
Handle
Cord Length
Safety Listings
Warranty
Specifications are subject to change without notice. Some values are approximate.

TROUBLESHOOTING

In COLUMN 3, the technician in the field can handle "FS" or Field Solutions. Others solutions should be handled by a repair technician – an
"AST" or Authorized Service Technician.
WARNING: Execute all the service procedures below only with power turned off, i.e. unplugged.
PROBLEM
Motor won't run
Motor runs but blade turns
erratically or scrapes
Unit vibrates excessively
FOR PARTS AND SERVICE CALL YOUR LOCAL DISTRIBUTOR,
or the Dri-Eaz Service Department at (360) 757-7776
Copyright 2002, Dri-Eaz Products, Inc.
Ace TurboDryer
6
1.0 amps
2,285 (3,882 CMH)
1230 Low - 1445 High
.50" (1.25 cm)
1/4 hp. TEAO
2-Speed PSC
Thermal Cut-off
2-Speed Rocker
16.5" Axial (41.9 cm)
24 x 20.3 x 19" (61 x 51.5 x 48.3 cm)
32 lb (16.3 kg)
39 lb (18 kg)
Yes
Molded
25 ft (7.6 m)
CE
7 Year Limited
CAUSE
No power to machine
Switch not turned on
Fan blade jammed
Intake or exhaust grill blocked
Switch is broken
Loose wiring
Severe jolt has caused motor mount to
bend and fan blade to rub
Accumulation of soil on fan blade
Fan blade has lost balance
Fan blade has been bent
Bent motor shaft
fire hazard.CLEAN EXTERIOR: Clean the housing with mild
detergent and water. Bring back the original shine with a vinyl
cleaner and polish like those used on automobile plastics.
EXTERIOR INSPECTION: Evaluate exterior components and
make sure they are properly installed. Listen to the unit for
abnormal sounds. Repair or replace components as needed.
Periodic Maintenance (as needed)
Make sure unit is unplugged and the blade has stopped. Re-
move four screws to remove each grill cover. This will permit
access to motor and fan blade for cleaning.
CLEAN COMPONENTS: Use compressed air or a vacuum to
remove lint and dust from fan blade, motor and grill covers.
DO NOT WET MOTOR OR WIRING: To prevent damage to
electrical components, do not use a hose or pressure washer
to clean a TurboDryer. If electrical components do become
wet, dry them immediately.
MOTOR BEARINGS: The bearings on all Dri-Eaz TurboDryers
are permanently lubricated. Do not oil.
See
above SOLUTION
FS Plug in the unit; check circuit breaker or fuse
FS Turn on the switch
FS Remove material jamming balde
FS Turn machine off and allow to cool, then remove blockage
AST Call distributor or Dri-Eaz for replacement switch
AST Check wiring and tighten as needed
AST Remove motor from housing, then replace or repair bent
motor mount
FS Clean fan blade
AST Balance or replace fan blade
AST Replace fan blade
AST Replace motor
3