Safety Regulations; Layout And Items Supplied - EINHELL TE-TS 254 T Manual De Instrucciones Original

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 115
Danger!
When using the equipment, a few safety pre-
cautions must be observed to avoid injuries and
damage. Please read the complete operating
instructions and safety regulations with due care.
Keep this manual in a safe place, so that the in-
formation is available at all times. If you give the
equipment to any other person, hand over these
operating instructions and safety regulations as
well. We cannot accept any liability for damage
or accidents which arise due to a failure to follow
these instructions and the safety instructions.
Explanation of the symbols used (see Fig. 26)
1. Danger! - Read the operating instructions to
reduce the risk of injury.
2. Caution! Wear ear-muff s. The impact of noi-
se can cause damage to hearing.
3. Caution! Wear a breathing mask. Dust
which is injurious to health can be generated
when working on wood and other materials.
Never use the device to work on any materi-
als containing asbestos!
4. Caution! Wear safety goggles. Sparks ge-
nerated during working or splinters, chips and
dust emitted by the device can cause loss of
sight.
5. Caution! Risk of injury! Do not reach into
the running saw blade.
6. Using the supplied ring wrench, turn the disk
clockwise to release the table insert. Turn the
disk counter-clockwise to secure the table
insert against falling out.
7. Conditions of the mains connection
8. Power rating
9. Speed
10. Cutting height at 90° and 45° saw blade angle
11. Saw blade dimensions
12. Thickness of the splitter
13. Weight

1. Safety regulations

The corresponding safety information can be
found in the enclosed booklet.
WARNING!
Read all safety warnings, instructions, illust-
rations and specifi cations provided with this
power tool. Failure to follow all instructions listed
below may result in electric shock, fi re and/or
serious injury.
Save all warnings and instructions for future
reference.
Anl_TE_TS_254_T_SPK13.indb 23
GB

2. Layout and items supplied

2.1 Layout (Fig. 1-25)
1. Saw table
2. Saw blade guard
3. Push stick
4. Blade
5. Splitter
6. Table insert
7. Complete parallel stop
8. Handwheel
9. Locking lever for saw blade angle
10. Pull-out table width extension
11. On/Off switch
12. Eccentric lever for parallel stop
13. Rotary disk
14. Cross stop
15. Screw for saw blade
16. Extractor adapter
17. Recessed head screw
18. Hole in splitter
19. Fastening lever
20. Fastening plate
21. Slot in saw table
22. Main scale
23. Stop rail
24. Additional scale
25. Slot in stop rail
26. Knurled screw for parallel stop
27. Washer for parallel stop
28. Lock bolt for parallel stop
29. Guide rail for parallel stop
30. Wrench 10/13 mm
31. Wrench 10/21 mm
32. Adjustment screw 0°
33. Adjustment screw 45°
34. Stop rail for cross stop
35. Knurled screw for cross stop
36. Locking screw for cross stop
37. Button cover for emergency stop switch
38. Cap on saw blade guard
39. Overload switch
40. Socket head screw 2.5 mm
41. Nut on parallel stop
42. Clamping lever for table width extension
43. Threaded sleeve
44. Nut
45. Locking grip for saw blade angle
2.2 Items supplied
Please check that the article is complete as
specifi ed in the scope of delivery. If parts are
missing, please contact our service center or the
sales outlet where you made your purchase at
- 23 -
10.01.2022 08:56:38

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

43.404.30

Tabla de contenido