Battery Installation; Precautions.concerning.batteries; Install.remote.control.batteries; Basic Operation - VIETA WH-SB500 Manual De Usuario

Install Remote Control Batteries
The.provided.Remote.Control.allows.the.unit.to.be.
operated.from.a.distance..
When.operating.the.Remote.Control,.point.it.. .
towards.the.remote.sensor.on.the.front.panel.of.the.
unit.
.Even.if.the.Remote.Control.is.operated.within.the.

effective.range.(5m),.remote.control.operation.may.
be.impossible.if.there.are.any.obstacles.between.the.
unit.and.the.remote.control..
.If.the.Remote.Control.is.operated.near.other

products.which.generate.infrared.rays,.or.if.other.
remote.control.devices.using.infrared.rays.are.used.
near.the.unit,.it.may.operate.incorrectly.
Conversely,.the.other.products.may.operate.
incorrectly..

Battery Installation

1..Remove.the.battery.compartment.cover..
2..Insert.two."AAA".(R03.or.UM-4).dry.batteries...
Make.sure.that.the.batteries.are.inserted.with.their.
positive." "±and.negative." ".poles.positioned.
correctly..
3..Close.the.cover..
Precautions Concerning Batteries
.Be.sure.to.insert.the.batteries.with.correct

positive." ".and.negative." ".polarities.
.Use.batteries.of.the.same.type..Never.use

different.types.of.batteries.together.
.Either.rechargeable.or.non-rechargeable

batteries.can.be.used..Refer.to.the.precautions
on.their.labels.
.When.the.Remote.Control.is.not.to.be.used.for.a

long.time.(more.than.a.month),.remove.the.
battery.from.the.Remote.Control.to.prevent.it.
from.leaking.
.If.the.batteries.leak,.wipe.away.the.leakage.

inside.the.battery.compartment.and.replace.the
.batteries.with.new.ones.
.Do.not.use.any.batteries.other.than.those

specified.Do.not.mix.new.batteries.with.old.ones.
.Do.not.heat.or.disassemble.batteries..Never

throw.them.in.fire.or.water.
.Do.not.carry.or.store.batteries.with.other.metallic..

objects..Doing.so.could.cause.batteries.to.short
circuit,.leak.or.explode.
.Never.recharge.a.battery.unless.it.is.confirmed..

to.be.a.rechargeable.type..

Basic Operation

Power

You.can.use.all.the.functions.on.the.panel.of.the.
unit.or.the.remote.control.after.connecting.to.power.
supply.(called.Standby.Mode).
Turning the System On
Press.the. .button.to.turn.the.system.on.from.
standby.mode.
Note:.When.turning.the.system.on,.the.system.will.
continue.in.the.mode.it.was.in.when.it.was.turned.off.
last.time.
Turning the System Off
Press.the. .button.again.to.turn.the.system.off.and.
go.to.standby.mode.
Note:.Be.sure.to.unplug.the.power.cord.from.the.
outlet.when.the.system.is.not.in.use.for.an.extended.
period.of.time.
Select the Correct TV System
Change.this.setting.if.the.video.does.not.appear.
correctly..By.default,.this.setting.matches.the.most.
common.setting.for.TV.in.your.country.
1..No.disc.mode,.press..the.SETUP.button.
2..Select..[Preference.Setup.Page].
3..Select..[TV.Type]..and.then.press.the..button.
4..Select.a.setting.and.then.press.the.ENTER.. .
button.
-.[PAL].-.For.TV.with.PAL.color.system.
-.[Auto].-.For.TV.that.is.compatible.with.both.. .
NTSC.and.PAL.(multi-system).
-.[NTSC].-.For.TV.with.NTSC.color.system.
5..To.exit.the.menu,.press.the.SETUP.button..
Change System Menu Language
1..Press.the.SETUP.button.
2..Select.[General.Setup.Page].
3..Select.[OSD.language].and.then.press.the..
button.
4..Select.a.setting.and.then.press.the.ENTER.button.
5..To.exit.the.menu,.press.the.SETUP.button.
Set the Clock
The.built-in.clock.shows.the.correct.time.in.the.
display.
1..In.standby.mode,.press.and.hold.the.CLOCK..
button.to.activate.the.clock.setting.mode,.hour..
indicator.will.blink.
2..Set.the.hour.with.the..button.or..button.
3..Press.the.ENTER.or.CLOCK.button.to.confirm,..
minute.indicator.will.blink.
ENGLISH
51