Publicidad
Mark the general area where fixture will be mounted. Using a small drill or nail,
make two small pilot holes at the marked locations. NOTE: Ensure mounting
location is within 5ft. of an electrical outlet.
Insert power cord connector into the end of
the fixture. Insert plug into an electrical outlet.
Use included cord clips for cord management.
FCC STATEMENT
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device
must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications to this unit not expressly approved by
the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: 1) Reorient or relocate the receiving antenna. 2) Increase the separation between the equipment and receiver. 3) Connect the equipment into
an outlet on a circuit different from that of the receiver. 4) Consult the dealer or an experienced radio/TV technician for help.
CARE AND MAINTENANCE
Periodically clean the fixture and diffuser using a mild, non-abrasive cleaner and soft cloth. When cleaning the fixture, make sure the power is turned off. Do not spray cleaner
directly onto any part of the fixture of LEDs.
6 YEAR LIMITED WARRANTY
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of (6) years from the date of original purchase by the consumer.
The fixture is not warrantied for use in a commercial or retail application. The warranty is limited to use in a residential environment. We will repair or replace (at our option) the
unit in the original color and style if available, or in a similar color and style if the original item has been discontinued, without charge. Defective units must be properly packed and
returned to the manufacturer with a letter of explanation and your original purchase receipt showing date of purchase. Call 1-800-291-8838 to obtain a return authorization number
and an address where to ship your defective product. Note: C.O.D. shipments will NOT be accepted. The liability of the manufacturer is in any case limited to replacement of the
defective light fixture product. The manufacturer will not be liable for any other loss, damage, labor costs or injury which is caused by the product. This limitation upon the liability
of the manufacturer includes any loss, damage, labor costs or injury which is (I) to person or property or otherwise; (II) incidental or consequential in nature; (III) based upon
theories of warranty, contract, negligence, strict liability, tort, or otherwise; or (IV) directly, or indirectly related to the sale, use, or repair of the product. This warranty gives you
specific rights, and you may also have other rights which vary from state to state.
Troubleshooting Guide
Problem
Fixture doesn't light.
Fuse blows or circuit breaker trips
when light is turned on.
Front light button
Before doing any work on the fixture, shut off power supply at the circuit breaker panel
to avoid electrical shock.
Cause
Power is off.
Bad connection.
Bad switch.
Discontinue use.
Hold the fixture in the marked location and drive wood screws until they
contact the bottom surface of the cabinet. The wood screws must be
driven in straight for the fixture to mount properly. DO NOT
OVERTIGHTEN to prevent stripping the screw hole. Replace screw
covers on both ends.
Touch Control
ON/OFF: Touch sensor to turn
on and off.
ON/OFF: Touch sensor to turn
on and off.
Dimming: Touch and hold
sensor to change the light
level.
Solution
Check if power supply is on.
Check cords and/or wiring.
Test or replace switch.
Call Customer Service Center
1-800-291-8838.
Back light button
Front light button
Replacement Parts List
Hardware Kit:
ZH-UC1181F18
Distributed by: Good Earth Lighting
Center Drive, Ste. 108 Mount Prospect, IL 60056
Printed in China
SAVE THESE INSTRUCTIONS.
1400 East Business
®
2
Publicidad
