Husqvarna CL400i Manual Del Usuario página 16

Battery charging status
A Husqvarna Li-ion battery can be charged or used at
all charging levels. The battery is not damaged. A fully
charged battery will not decrease its charge when the
battery is left in the charger.
LED display
LED 1 flashes
LED 1 is lit, LED 2 flashes 25%-50%
LED 1, LED 2 are lit, LED
3 flashes
LED 1, LED 2, LED 3 are
lit, LED 4 flashes
LED 1, LED 2, LED 3,
LED 4 are lit
To do before you operate the product
1. Water the ground the day before operation during
the summertime or if the soil is dry.
2. Make sure that people, animals are at least 20 m
away from the product.
3. Put the cable onto the cable winder. Refer to
install the cable on page 14 .
4. Adjust the cable laying depth. Refer to
cable laying depth on page 16 .
5. Attach the end of the cable to a stake.
To start the product
1. Tilt the handlebar to the side. Refer to
handlebar on page 16 .
2. Open the battery lid.
3. Put a charged battery in battery slot number 1 below
the battery lid. For longer operation time, put a
second charged battery in battery slot number 2.
4. Disconnect the safety key from the safety key holder.
5. Push the safety key into the safety lock. (Fig. 32)
6. Stay behind the product.
7. Push the standby button (A) on the control panel.
The standby light (B) comes on. (Fig. 33)
8. Push the start/stop button (C) until it stays pushed in.
The motor starts.
CAUTION:
product if the warning light (D) flashes
red.
9. Push the drill operation bail in the direction of the
handlebar to engage the drill. (Fig. 34)
16
Charging status
0%-25%
50%-75%
75%-100%
Fully charged
To
To adjust the
To tilt the
Do not operate the
To use the drive on the wheels
• Pull the drive control bail (A) in the direction of the
handlebar to engage the drive on the wheels. (Fig.
35)
• Release the drive control bail to disengage the drive
on the wheels.
To adjust the cable laying depth
1. Loosen the knob (A). (Fig. 36)
2. Adjust the support wheel (B) to the necessary cable
laying depth and tighten the knob.
Note:
The numbers (C) on the side of the support
wheel tube show the cable laying depth in cm. The
cable laying depth can be adjusted between 1–6 cm.
To adjust the height of the handlebar
The height of the handlebar can be adjusted into 5
positions.
1. Turn the handle (A) counterclockwise to loosen it
and remove the knob (B). (Fig. 37)
2. Adjust the height of the handlebar and install the
knob in the hole of the nearest position.
3. Turn the handle clockwise to tighten it.
To tilt the handlebar
You can tilt the handlebar to prevent that obstacles hit
you when you operate the product. The handlebar can
be tilted in 4 positions on the right side and 4 positions
on the left side.
1. Pull the handlebar tilt bail (A) in the direction of the
handlebar fully and hold it. The handlebar tilt bail is
on the lower left side of the handlebar. (Fig. 38)
2. Tilt the handlebar to 1 of the 4 positions to the left
or right side and release the handlebar tilt bail. Make
sure that the pin that lock the handlebar position is in
1 of the slots. (Fig. 39)
To lock the swivel function of the
feeding fin
To increase the precision of direction when you put the
cable in long straight sections, you can lock the swivel
function of the feeding fin.
• Make sure that the feeding fin is in the same
direction as the product and tighten the handle (A).
(Fig. 40)
To adjust the cable guide
The product is adjusted for 4 mm cables. If the cable
has a larger diameter, the cable guide must be adjusted.
1. Loosen the 2 screws. (Fig. 41)
2. Move the cable guide up a few millimeters.
1698 - 001 - 21.01.2022