Correction Of Malfunctions; Repair Service - stayer EPG 300 Manual De Instrucciones

gb
Adjustment operation (Fig. 7)
Preparing for Operation
Spraying on the sides of water bodies (lakes, rivers,
etc.) or neighbouring surfaces in the direct catchment
area is not permitted.
When purchasing paint, varnish and spray material, pay
attention to their environmental compatibility.
Preparing the Spray Surface
Cover off the vicinity of the spray surface thoroughly
and generously.
The spray mist contaminates the environment. When
spraying in enclosures, surfaces not covered can become
contaminated. The spray surface must be clean, dry and
grease-free
- Roughen smooth surfaces and then remove the
sanding dust.
Preparation of material (fig .11)
1. Mix the material well befare measuring viscosity.
2. Completely submerge the cup viscometers, in the
material to be sprayed.
3. Hold the cup test and measure time in seconds
until all the liquid is emptied and this corresponds
to time (seconds)
supplied as appropriate,
Table Preparation of material:
Material
Oil Painting
Olio Primer
Coating

Correction of Malfunctions

See table page 17 and 18
Maintenance and service instructions
Before any work on the machine irself, pull the mains
plug.
Cleaning (Fig. 9)
Never immerse the electrical unit into solvent or
water.
Clean the housing using only a moist cloth.
Proper cleaning is the requirement for flawless operation
of the spray gun. lmproper or lack of cleaning voids
warranty claims.
Always clean the spray gun and the container
with the respective diluting agent (paint thinner
or water) for
Never clean the nozzle and air hales of the spray gun with
pointed metal objects. Do not pour diluted spray material
back into the original spray material drum/tin for storage.
depending on the
in the following
Time (sec)
25-40
30-45
20-50
the spray material being
Clean the spray gun thoroughly after having sprayed
material hazardous to one's health.
- Unplug the mains plug and pull the trigger switch 16
so that the spraying material can flow back into the
container.
- Remove the electrical unit.
- Unscrew the container 11 and empty the remaining
spray material.
- Fill diluting agent (paint thinner or water) into the
container and screw it to the spray gun.
- Shake the spray gun several times.
- Connect the spray gun to the electrical unit again.
- Plug the mains plug into a socket outlet, pull the trigger
switch and spray the diluting agent into an empty
material tin.
- Repeat the process until clear diluting agent emerges
from the spray gun.
Unplug the mains plug and remove the electrical unit.
- Completely empty the container 11.
- Check if the suction tube with the container seal is free
of spray material and undamaged.
- Clean the outside of the container and the spray gun
with a cloth moistened in paint thinner.
- Unscrew the un ion nut 14and the air cap 13.
material
- Clean the nozzle 20 and the nozzle needle with diluting
table.
agent.
From time to time, the nozzle seal 21 must also be
cleaned.
- Mount the air cap 13 onto the nozzle and tighten with
the un ion nut 14.
Changing the Air Filter (Fig.10)
Never operate the power tool without the air filter.
With out the air filter, dirt/contamination con be drawn
in and can influence the operation of the power tool.
The air filter must be replaced when soiled.
- Remove the air filter cover 3, taking into account the 7
hooks that hold the filter cover 3.
- Replace the air filter 8.
- Reattach the air filter cover and screw in the screw
again.

Repair service

Our after-sales service responds to your questions
concerning maintenance and repair of your product as
well as spare parts. Exploded views and information on
spare parts can also be found under:
info@grupostayer.com
Our customer consultants answer your questions
concerning best buy, application and adjustment of
products and accessories.
used.
/ /
22