Velleman CCTVPROM11 Guía Rápida página 6

rea ar panel
VID DEO IN 4 video o input chan
MO ONITOR connec ct a CRT mo
AU UDIO IN 1 audio o input chan
AU UDIO OUT 1 audio o output to c
LA N port Connec ct the DVR t
VG GA connec ctor for video
EX XTERNAL I/O use a 9 9 pin DSUB c
19 V DC Power
6. . Hardwa are setup p
In stalling the e Hard Disk k Drive (HD
•
Obtain a su uitable HDD (not included
be formatte ed.
•
Make sure e to unplug t the device fr
to avoid ele ectrostatic di ischarge.
•
Unscrew th e 6 screws ( (1 on either
•
Lift the cov er (back firs st).
•
Screw the m mounting bra ackets on th
Note: the e PCB must b be facing up
•
Connect the e SATA data
•
Screw the H HDD on the
•
Close the co over (front f first) and sec
A A
power supply
Co onnecting a a video mon nitor
•
Obtain a su uitable monit tor (not incl.
Note: when n both a CRT T and VGA m
force the output
Co onnecting th he power s supply
•
Plug the DC C output con
WARNING: W only use the e included a
•
Plug the inc cluded powe
not switch the DVR on
Co onnecting a a camera
•
Connect the e video outp put of the ca
Note: video o system is d detected aut
befo re the DVR
Co onnecting a audio
•
The DVR su upports one
DVR. Conne ector type is s RCA.
•
There is als so an audio o output conne
desired. Co nnector type e is RCA.
Co onnecting L Local Area N Network (L
V. 03 - 17/01/20 012
All manuals and user guides at all-guides.com
CC CTVPROM
nnels to conn nect 4 extern
nitor to this output
nnel to conne ect an extern
connect to a n audio dev
to a local net twork by plu
o monitor
connector to o connect ex
supply input t.
DD)
d), type SAT TA (Serial Ad
om the main ns before se
side and 4 o on the back)
he HDD (scre ews included
wards when mounting t
cable and p power supply y to the HDD
bottom of th he DVR hous sing PCB faci
cure it with t the 6 screws
B
data bus (SA d ATA)
) and conne ect it to the B
monitor are c connected, p
to the CRT m monitor port t.
nector of th e power ada aptor into the
daptor.
r cable into the adaptor input conne
yet.
mera to eith her video inp
tomatically; therefore it
is powered-o on.
audio input . Connect th e audio outp
ector. Conne ect an audio
AN)
11
nal video sou urces.
nal audio so urce e.g. fro
ice, e.g. a sp peaker (mon
ugging a netw work cable i
xternal signa ls e.g. alarm
dvanced Tec hnology Atta
rvicing and d do not touc
that hold th he cover in p
d).
he HDD into o the DVR.
D.
ing upwards using the in
s.
*HDD n
BNC or VGA video outpu
press and ho old the
e 19VDC pow wer input at
ector and plu ug the other
put at the ba ck of the DV
is important t that the ca
put of an aud dio source to
device e.g. a speaker to
6
om a camera a with audio.
no).
nto this port t.
m, sensor, ... .
achment). T he HDD mus
h any electr onic circuitry
place.
ncluded scre ws.
not included
ut on the bac ck of the DVR
but tton during s start-up to
the back of f the DVR.
end into the e mains. Do
VR. Connecto or type is BN NC.
ameras are p power-suppli
o the audio i input of the
o this conne ctor when
n nv
©Velleman
.
st
y
R.
ied