HiLook PTZ-T5225I-A Guia De Inicio Rapido página 12

Switch
Video Output
CVBS
Table 1-18 Set Terminal Resistor
Switch
Description
Turn on the Resistor
Turn off the Resistor
4. DIP Switch of 7-inch IR Speed Dome
Table 1-19 Switch Functions
Switch No.
1 to 8 (SW1) Set the address for the speed dome
1 to 2 (SW2) Set the baud rate for the speed dome
3 to 5 (SW2) Set the protocol for the speed dome
Set the video output mode for the
6 to 7 (SW2)
speed dome
Set the terminal resistor for the speed
8 (SW2)
dome
Table 1-20 Set Dome Address
Dome
Address 1 2 3
0 OFF OFF OFF OFF OFF
1 ON OFF OFF OFF OFF
OFF ON OFF OFF OFF
2
ON ON OFF OFF OFF
3
... ... ...
...
ON ON ON ON ON
255
Table 1-21 Set Baud Rate
DIP Switch SW2-Baud Rate Settings
Baud rate
2400
4800
9600
19200
Table 1-22 Set Protocol
DIP Switch SW2-Protocol Settings
Protocol 3
Self-adaptive OFF
PELCO_P ON
PELCO_D OFF
HIKVISION ON
VICON OFF
KALATE ON
MAN_BOSCH OFF
MAN_AD ON
Note:
The No.6, No.7 SW2 switches are for setting the video
output mode of the speed dome.
Table 1-23 Set Video Output
Switch
Video Output
TVI
AHD
CVI
CVBS
Table 1-24 Set Terminal Resistor
Switch
Description
Turn on the Resistor
Turn off the Resistor
5. Wall Mounting for Outdoor Device
1. Install the bracket.
2. Set the DIP Switch and install the speed dome.
3. Fasten the lock screws.
Protective Measures for Outdoor Installation (Page 7–C)
Application and Operations
1. System Application
The device can be controlled through the back-end device or
control software. The back-end device includes control
keyboard, DVR (Digital Video Recorder), etc., and the control
software includes client software. Here we take the
connection of DVR as the example.
HD-TVI Speed Dome·Quick Start Guide
8 9
ON ON
10
ON
OFF
Function
SW1
4 5 6 7 8
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
OFF OFF OFF
... ... ... ... ...
ON ON ON
1 2
OFF OFF
ON OFF
OFF ON
ON ON
4 5
OFF OFF
OFF OFF
ON OFF
ON OFF
OFF ON
OFF ON
ON ON
ON ON
6 7
OFF OFF
ON OFF
OFF ON
ON ON
8
ON
OFF
Notes:
 If both the speed dome and the DVR support the coaxial
function, the RS-485 cable is not necessary.
 The HD-TVI video output can only be connected to specific
HD-TVI DVR.
2. Basic Operations
Make sure the speed dome is connected properly, and the
following basic operations are supported:
Panning and tilting:
Click the direction buttons to control the pan and tilt
movement of the speed dome.
Zooming:
Click the ZOOM+ and ZOOM- buttons to control the zooming.
Focusing:
Click the FOCUS+ and FOCUS- buttons to adjust the focus.
Iris:
Click the IRIS+ and IRIS- buttons to adjust the iris.
Preset control:
The speed dome supports the preset function, and the
configurable preset range varies according to the control
system. The system menu pops up after you call the No.95
preset
The main menu interface is shown as follows:
Figure 1-1 Main Menu
Note:
Refer to the user manual for the detailed instruction to set the
speed dome.
2.1 Configuring Patrol
You can set the patrol function by the DVR and OSD menu, as
well as the one-touch patrol can be realized.
 Configuring Patrol by DVR
Steps:
1. Enter the PTZ Control interface: Menu>Camera>PTZ.
Figure 1-2 PTZ Settings
2. Select patrol No. in the drop-down list of patrol.
3. Click the Set button to add key points for the patrol.
Figure 1-3 Key Point Configuration
4. Configure key point parameters, such as the key point No.,
duration of staying for one key point and speed of patrol. The
key point is corresponding to the preset. The Key Point No.
determines the order at which the PTZ will follow while cycling
through the patrol. The Duration refers to the time span to
11