Led Light - EINHELL TE-DA 18/760 Li Manual De Instrucciones

If any dirt collects in the storage drum for the
cleaning coil (5), you can rinse it out of the drum
with clear water by opening the two cleaning/
emptying openings for the storage drum (6) and
continue rinsing until there is no more dirt in
the storage drum for the cleaning coil (5). Then
remove all the remaining water from the storage
drum for the cleaning coil (5) and leave the two
cleaning/emptying openings for the storage drum
(6) open until the drum is completely dry.
The two cleaning/emptying openings for the sto-
rage drum (6) must be closed again before the
machine is used the next time.
6.5 Replacing the cleaning coil (Fig. 1.1)
A damaged or worn cleaning coil can be replaced
by a new one. To do so, pull the cleaning coil out
of the machine until you can see the connecting
piece (8). The screw on the connecting piece
must be undone. Now you can simply pull off the
old cleaning coil (1) and fi t the new one in reverse
order. Finally check that the screw on the connec-
ting piece (8) is tight. The new cleaning coil (1)
can now be moved into the storage drum for the
cleaning coil (5).

6.6 LED light

Press the On/Off switch (4) to switch on the LED
light (7). You will then have a better view of the
work area. When you let go of the On/Off switch
(4) the light will continue to shine for another 10
seconds or so before it goes out.
6.7 Charging the Li battery pack (Fig. 2+3)
1. Remove the battery pack (a) from the handle,
pressing the pushlock button (b) downwards
to do so.
2. Check that your mains voltage is the same as
that marked on the rating plate of the battery
charger. Insert the power plug of the charger
(c) into the mains socket outlet. The green
LED will then begin to fl ash.
3. Push the battery pack onto the battery char-
ger.
In section 10 (Charger indicator) you will fi nd a
table with an explanation of the LED indicator on
the charger.
Anl_TE_DA_18_760_Li_SPK13.indb 18 Anl_TE_DA_18_760_Li_SPK13.indb 18
GB
If the battery pack fails to charge, check for the
following:
•
voltage at the power socket
•
whether there is good contact at the charging
contacts of the charging unit
If the battery pack still fails to charge, send
•
the charger and charging adapter
•
and the battery pack
to our customer service center.
To ensure that items are properly packaged
and delivered when you send them to us,
please contact our customer service or the
point of sale at which the equipment was
purchased.
When shipping or disposing of batteries and
cordless tools, always ensure that they are
packed individually in plastic bags to prevent
short circuits and fi res.
To ensure that the battery pack provides long ser-
vice, you should take care to recharge it promptly.
You must recharge the battery pack when you
notice that the performance of the device drops.
Never allow the battery pack to become fully di-
scharged. This will cause it to develop a defect.
6.8 Battery capacity indicator (Fig. 4/Pos. e)
Press the button for the battery capacity indicator
(d). The battery capacity indicator (e) shows the
charge status of the battery using 3 LEDs.
All 3 LEDs are lit:
The battery is fully charged.
2 or 1 LED(s) are lit:
The battery has an adequate remaining charge.
1 LED fl ashes:
The battery is empty, recharge the battery.
All LEDs blink:
The battery temperature is too low. Remove the
battery from the equipment, keep it at room tem-
perature for one day. If the fault reoccurs, this me-
ans that the rechargeable battery has undergone
exhaustive discharge and is defective. Remove
the battery from the equipment. Never use or
charge a defective battery.
- 18 -
23.02.2022 13:24:14 23.02.2022 13:24:14