Pc Opera Tion; Inst Alla Tion Menu - Sanyo CE32LM5R Manual De Instrucciones

GB
PC menu settings
OSD Language, Timer and AV2 settings are the same as in all
input modes (pg 8).
Power save if turned ON will switch the monitor into Powersave
mode after 1 minute if no signal is detected, the LED light will turn a
brighter blue to indicate stand by. The monitor will automatically turn
back on when a signal has been detected (PC input / RGBHV / DVI).
Use1 or 2 buttons to select power save ON or OFF.
Press the menu button twice to initiate Powersave.
Installation Menu
Installation
ON Program OFF
Max Volume
OSD ON/ OFF
Winter mode ON/ OFF
RC Inhibition ON/ OFF
Child Lock ON/ OFF
Address 000-999
Baud Rate 9600 / 19200
: Select
This LCD monitor allows you to set up the following:-
SETTING PROCEDURE
1 . Press and hold the green button on the Remote control
handset for 5 seconds.(Installation menu will appear)
2. Use the 5 or 6 button to highlight each option, use the 1 or
2 button to adjust each option.
■ On Program
Select ON program using the 5 or 6 button, select the start up
position using the 1 or 2 buttons.
(Off / AV1 / RGB/ AV2/ AV3/ DVI/ PC)
Press the MENU button to exit the menu.
■ Max Volume
Select Max volume using the
2 buttons to set the maximum volume required.
■ OSD (On screen display)
Select OSD using the 5 or 6 button, select ON / OFF using the
1 or 2 buttons.Selecting OFF will inhibit the OSD. To re-
instate OSD, press and hold the green button on the remote control
to re-enter installation menu and select OSD ON.
■ Winter mode
This Function can be activated when the LCD monitor is used during
cold temperature conditions, approximately 38˚F/ 4˚C or below to
maintain picture performance.
Using the 5 or 6 button select winter mode, once highlighted
you can select ON or OFF by pressing the 1 or 2 button.
IMPORTANT: The AC cord should not be disconnected during the
operation of Winter mode function.
When in winter mode, power consumption is higher than normal
standby consumption. This is entirely due to the operation of heating
circuitry. We strongly recommend to turn off Winter mode when the
ambient temperature is above 38˚F/ 4˚C.
■ RC Inhibition
You can prevent unwanted remote control operation by selecting RC
Inhibition. When selected an inhibit symbol will appear on screen
when a button is pressed on the remote control.
Select using the 5 or 6 button. Press the 1 or 2 button
to select On or OFF.
To re-instate RC operation press and hold the green button on the
remote control and select RC inhibition OFF.
■ Child lock
You can prevent unwanted operation of the LCD monitor via the
buttons on the bottom edge of monitor.
Select using the 5 or 6 button. Press the 1 button to select
On or OFF.
✐ Disconnecting the mains suppy before exiting installation menu
will cancel the following features On program, RC inhibition, Address
and Baud Rate.
PC OPERA TION /
PC OPERA TION /
/ AV1-AV3 /RGB/ DVI/ PC
: Adjust : Exit
MENU
5 or 6 button, use the 1 or
INST ALLA TION MENU
INST ALLA TION MENU
This monitor can be controlled via the RS232C connector using a
suitable computer/ control commands.
Serial Interface Specification
Transfer Specification
1. Transmission Speed: initial setting value is 19200.
2. Transmission speed can be changed via the Installation menu.
(see below baud rate)
ITEM
Synchronous system
Transmission Speed
Data Length
Parity
Stop Bit
Flow Control
Connection
The Designated RS-232C serial cable must be used for a
connection to a computer and LCD monitor.
CD
RXD
TXD
DTR
SG
DSR
RTS
CTS
RING
The TV command is defined by one command/ one line that starts
with "C" and ends with carriage return. (0x0D)
There are two types of commands:
Functional Execution Command e.g Co5[CR] (table on page 64)
Status Read Commands e.g "CR0 [CR] (see table on page 64)
Setting the monitor address in RS232 mode
To Access Installation mode press the green button on the remote
control and hold for 5 seconds. A new screen will appear.
Installation
ON Program
Max Volume
OSD
Winter mode
RC Inhibition
Child Lock
Address
Baud Rate
: Select
Each monitor can have a specific Address for example 007, which
enables the monitor to be controlled individually and will not affect
other monitors connected to a controlling PC.
Address format command
The addressing format command is used for operating multiple
monitor sets from a single PC via the RS232C command line. If you
set your monitor address to '000', it will never respond to any
addressing command from the PC.
If the address from the PC is 'FFF', all monitor sets will execute the
command.
The Address format command is defined by one command, one line
which starts with 'A' and ends with carriage return.(0 x0D)
The Monitor starts to decode when it receives a carriage return.
(0x0D)
An address is added at the top of a control command
Example:
Functional execution command:
"A001C05" [CR] means address is 001 and the control command is
C05
Status read command
"A001CR0"[CR] means address is 001 and command is CR0.
The monitor can set its own address in the Installation option menu
(above) The address range is 000 - 999, the default address will be
000.
The baud rate indicates the unit for transfer speed of data
from the PC to the monitor sets.
RS232C settings
SPECIFICATION
Asynchronous
9600 / 19200
8 bit
None
1
None
PC
TV CONTROL
COM 1
PORT
1
1
N.C.
2 2
RXD
3 3
TXD
4
4
N.C
5 5
SG
6 6
N.C
7
7
RTS
8
8
CTS
9 9
N.C.
(D-Sub 9 Pin) (D-Sub 9 Pin)
OFF / AV1-AV3 /RGB/ DVI/ PC
ON/ OFF
ON/ OFF
ON/ OFF
ON/ OFF
000-999
9600 / 19200
: Adjust
GB
: Exit
MENU
9