Alarm Setting; Comfort Level; Weather Forecast Symbols; Battery Replacement - TFA 35.1098.54 Instrucciones De Uso

TFA_No. 35.1098.54_Anleitung
QUADRO – Wireless weather station
7.2 12 and 24 hours system indication
• Press UP button in normal mode to choose 12 HR or 24 HR system.
• In 12 HR system PM appears on the display after 12 h.

7.3 Alarm setting

• Press and hold ALARM button.
• AL appears on the display.
• The hour digit is flashing. Press UP or DOWN button to adjust hours.
• Press ALARM button again and you can adjust the minutes with the UP or DOWN but-
ton.
• Holding UP or DOWN button, you will enter fast mode.
• Confirm with ALARM button and the display shows the current time.
• Press ALARM button again and the alarm function is activated.
• appears on the display.
• Once the alarm starts to ring (4 different sounds),
• Press any button to stop the alarm.
• You can activate the snooze function by pressing the SNZ button.
• and are flashing and the alarm will be interrupted for 5 minutes.
8. Thermometer and hygrometer
8.1 Display change °C/°F
• Press DOWN button to change between °C (Celcius) or °F (Fahrenheit) as temperature
unit.
8.2 Trend pointer
• The trend pointer displayed on the LCD indicates if the temperature is increasing,
steady or decreasing.

8.3 Comfort level

• On the display appears a smiling or sad face icon to indicate the comfort level of
indoor climate.

8.4 Weather forecast symbols

• There are 5 different weather symbols (sunny, slightly cloudy, cloudy, rainy, strong
rain).
• The weather symbol is based on the changes of humidity values of the outdoor sensor.
9. Moon phase display
• The moon phase of each day is shown on the LCD.
10. Additional transmitters
• For having more than one external transmitter, select different channels for each
sensor by the 1/2/3 switch. The new transmitter will be received automatically by the
base station.
• The outdoor values measured by the sensor are shown on the display of the base
station. If you have installed more than one transmitter, press CHANNEL button to
change between the outdoor transmitters.
14
19.04.2022 12:03 Uhr Seite 8
flashes.
QUADRO – Wireless weather station
• To cancel an unused channel hold CHANNEL button for 3 seconds. If a new channel is
received it will be automatically registered again.
11. Positioning of base station and the transmitter
• With the foldable leg at the back of the unit, the base station can be placed onto any
flat surface or wall mounted at the desired location by the hanging hole at the back of
the unit. Avoid the vicinity of any interfering field like computer monitors or TV sets
and solid metal objects.
• Choose a shady and dry position for the transmitter. (Direct sunshine falsifies the
measurement and continuous humidity strains the electronic components needlessly).
• Check the transmission of 433 MHz signal from the transmitter to the base station
(transmission range 100 m free field). Within ferro-concrete rooms (basements,
superstructures), the received signal is naturally weakened.
• If necessary choose another position for transmitter and/or base station.
• To wall mount the transmitter, use a nail to affix the transmitter to the desired wall.
12. Care and maintenance
• Clean the instrument with a soft damp cloth. Do not use solvents or scouring agents.
• Remove the batteries if you do not use the product for a long period of time.
• Keep the instrument in a dry place.

12.1 Battery replacement

• Change the batteries when the battery symbol of the station or the transmitter appears
on the display.
• Please note: When the batteries are changed, the contact between transmitter and
receiver must be restored – so always insert new batteries into both units or start a
manual transmitter search.
13. Troubleshooting
Problems Solution
➜ Observe correct polarity when inserting the batteries
No indication on the
➜ Change the batteries
base station/transmitter
➜ No transmitter installed
No transmitter reception
➜ Check batteries of external transmitter
Display "---"
for channel 1/2/3 (only use batteries/rechargeable batteries with 1.5V
voltage!)
➜ Restart the transmitter and the base station according
to the manual
➜ Start manual search for the transmitter
➜ Choose another place for the transmitter and/or the
base station
➜ Reduce the distance between the transmitter and the
base station
➜ Check if there is any source of interference
15