Rotation Only - Makita HR008G Manual De Instrucciones

Reversing switch action
► Fig.6: 1. Reversing switch lever
CAUTION:
Always check the direction of
rotation before operation.
CAUTION:
Use the reversing switch only after
the tool comes to a complete stop. Changing the
direction of rotation before the tool stops may dam-
age the tool.
CAUTION:
When not operating the tool,
always set the reversing switch lever to the neu-
tral position.
This tool has a reversing switch to change the direction
of rotation. Depress the reversing switch lever from the
A side for clockwise rotation or from the B side for coun-
terclockwise rotation.
When the reversing switch lever is in the neutral posi-
tion, the switch trigger cannot be pulled.
Changing the quick change chuck
for SDS-plus
For model HR009G
The quick change chuck for SDS-plus can be easily
exchanged for the quick change drill chuck.
Removing the quick change chuck
for SDS-plus
CAUTION:
Before removing the quick change
chuck for SDS-plus, be sure to remove the bit.
Grasp the change cover of the quick change chuck for
SDS-plus and turn it in the direction of the arrow until
the change cover line moves from the
the symbol. Pull the quick change chuck for SDS-
plus, forcefully if necessary, in the direction of the arrow.
► Fig.7: 1. Quick change chuck for SDS-plus
2. Change cover 3. Change cover line
Installing the quick change drill
chuck
Check the line of the quick change drill chuck shows
the symbol. Grasp the change cover of the quick
change drill chuck and set the line to the
Place the quick change drill chuck on the spindle of the
tool. Grasp the change cover of the quick change drill
chuck and turn the change cover line to the
until a click can clearly be heard.
► Fig.8: 1. Quick change drill chuck 2. Spindle
3. Change cover line 4. Change cover
Selecting the action mode
NOTICE:
knob when the tool is running. The tool will be damaged.
NOTICE:
change mechanism, be sure that the action mode
changing knob is always positively located in one
of the three action mode positions.
Rotation with hammering
For drilling in concrete, masonry, etc., rotate the action
mode changing knob to the
carbide tipped bit (optional accessory).
► Fig.9: 1. Rotation with hammering 2. Action mode

Rotation only

For drilling in wood, metal or plastic materials, rotate
the action mode changing knob to the
twist drill bit or wood drill bit.
► Fig.10: 1. Rotation only
Hammering only
For chipping, scaling or demolition operations, rotate
the action mode changing knob to the
bull point, cold chisel, scaling chisel, etc.
► Fig.11: 1. Hammering only
Air duct
duct or do not insert any other object into the air duct.
Otherwise you may get injured or the tool may get damaged.
symbol to The air duct is designed to improve the suction perfor-
mance of the dust collection system. For details on how
to install the dust collection system, refer to the instruc-
tions on installing the dust collection system.
► Fig.12: 1. Air duct
Hook
Optional accessory
hanging the tool with the hook.
symbol.
tion or on potentially unstable surface.
symbol
The hook is convenient for temporarily hanging the tool.
Before installing the hook, remove the rubber cap from the screw
holes in the mounting bracket. Insert the plate washers under the
bracket, and then tighten the hook with screws in place.
► Fig.13: 1. Rubber cap 2. Mounting bracket 3. Plate
For use, lift up the arm of the hook until it snaps into the open position.
When not in use, be sure that the hook is folded back in
the closed position.
► Fig.14: 1. Hook 2. Open position 3. Closed position
► Fig.15
18 ENGLISH
Do not rotate the action mode changing
To avoid rapid wear on the mode
changing knob
CAUTION:
Do not put your finger into the air
CAUTION:
Always remove the battery when
CAUTION:
Never hook the tool at high loca-
washers 4. Hook 5. Screws
symbol. Use a tungsten
symbol. Use a
symbol. Use a