Tabla De Contenido; Index; Product Specifications - KNOVA KN WL-12M Manual Del Usuario

INDEX

Index .................................................................................
Product specifications ......................................................
Safety instructions ...........................................................
Electrical requirements ....................................................
Accessories and attachments ..........................................
Carton contents ...............................................................
Installation ........................................................................ 3

PRODUCT SPECIFICATIONS

Attention: Please choose proper power source, voltage and frequency that are shown in the label for your lathe.
Model
Motor power:
Swing over bed:
Distance between centers:
Spindle taper:
SAFETY INSTRUCTIONS
WARNING
When using electric tools, basic safety precautions, including the following, should always be followed
to reduce the risk of fire, electric shock and personal injury. Read all these instructions before operating this product
and save the instructions.
GENERAL
1. Read and understand manual.
For your own safety, read and understand the entire
instruction manual before operating the lathe.
2. Read and understand warning label.
Read and understand the warning labels posted on
the machine. Failure to comply with all of these labels
may cause serious injury.
3. Keep work area clean.
Cluttered areas and benches invite injuries.
4. Consider work area environment.
Do not expose power tools to rain. Do not use power
tools in damp or wet locations. Keep work area well lit.
Do not use power tools where there is risk to cause fire
or explosion.
5. Guard against electric shock.
Avoid body contact with earthed or grounded surfaces
(e.g. pipes, radiators, ranges, refrigerators).
6. Keep children away.
Do not let visitors touch the tool or extension cord.
All visitors should be kept away from work area.
7. Store idle tool.
When not in use, tools should be stored in a dry,
high of locked up place, out of reach of children.
8. Do not force the tool.
It will do the job better and safer at rate for which
it was intended.
9. Use the right tool.
Do not force small tools or attachments to do the job of
a heavy duty tool. Do not use tools for purposes not
intended; for example, do not use circular saws to cut
tree limbs or logs.
10. Dress properly.
Do not wear loose clothing or jewellery, they can be
caught in moving parts. Rubber gloves and non-skid
footwear are recommended when working outdoors.
Wear protecting hair covering to contain long hair.
KN WL-12M
3/4 HP (500 watts)
12" (305 mm)
18" (455 mm)
MT2
1 Adjusting .........................................................................
1 Operation ........................................................................
1 Maintenance ...................................................................
2 Troubleshooting .............................................................. 10
3 Parts list ..........................................................................
3 Assembly diagram ..........................................................
Notes .............................................................................. 26
430 - 2,800 RPM (50 Hz)
Spindle speed:
520 - 3,400 RPM (60 Hz)
Tailstock taper:
MT2
Tool rest:
7-7/8" (200 mm)
Face plate:
Ø 3-5/32" (80 mm)
11. Use safety glasses and hearing protection.
Also use face or dust mask if the cutting
operation is dusty.
12. Do not abuse the cord.
Never carry the tool by the cord of yank it to disconnect
it from the socket, Keep the cord away from heat,
oil and sharp edges.
13. Do not overreach.
Keep proper footing and balance at all times.
14. Maintain tools with care.
Keep cutting tools sharp and clean for better and safer
performance. Follow instructions for lubrication and
changing accessories. Inspect tool cord periodically and
if damaged have it repaired by an authorized service
facility. Inspect extension cords periodically and replace,
if damaged. Keep handles dry, clean and free from oil
and grease.
15. Disconnect tools.
When not in use, before servicing and changing
accessories such as blades, bits and cutters,
disconnect tools.
16. Remove adjusting keys and wrenches.
Form the habit of checking to see that keys and
adjusting wrenches are removed from the tool before
turning it on.
17. Avoid unintentional starting.
Do not carry a plugged-in tool with a finger on the switch.
Ensure switch is off when plugging in.
18. Use outdoor extension leads.
When tool is used outdoors, use only extension cords
intended for outdoor use.
19. Stay alert.
Watch what you are doing. Use common sense.
Do not operate tool when you are tired.
1
5
5
9
11
12
Net / gross
weight:
28 / 30 kg