Start-Up Instructions; Usage Instructions; Changing The Batteries - Arregui CI10 Manual De Instrucciones

START-UP INSTRUCTIONS

WE RECOMMEND CONFIGURING THE REMOTES BEFORE INSTALLING THE
LOCK ON THE DOOR.
INSERT THE LOCK'S ANTENNA AND BATTERIES:
• Insert the antenna (P). Remove the lock's cover casing (A) by unscrewing the
golden screw on the side. Insert the batteries (J) (4 x AA) and the emergency
battery (K) (12V).
• Check the magnet is positioned correctly inside the bolt storage part (it must
always be installed opposite the lock's bolts).
CONFIGURATION OF REMOTE CONTROLS TO OPEN THE LOCK:
• Remove the protective plastic cove-
ring the battery to activate the remotes.
• Position the remotes near the lock.
• Step 1: With the help of the Allen key
(N), press registration button A on the
lock twice, pressing and holding the bu-
tton the second time until the remotes
are confi gured (there will be a beep each time the button is pressed).
• Step 2: Press button A on each remote you wish to sync to the lock, pres-
sing it once (it will beep twice once synced). During step 2, you can confi gure
all remotes by pressing button A on each of them quickly and consecutively.
Remember that you must press and hold button A on the lock throughout the
entire process.
If a certain amount of time passes between the confi guration of two remotes,
you must repeat step 1 before confi gu-
ring each remote.
• Check that all remotes work by ope-
ning and closing the lock.
CONFIGURATION OF REMOTE
CONTROLS FOR EMERGENCY LOCK
OPENING:
Follow the same steps detailed in the
previous section, but press registration
button B on the lock and press button
B on the remote controls.
Close
(A) Open lock
(B) Emergency opening

USAGE INSTRUCTIONS

CLOSING
To close the lock, press the ( ) button on the remote control. Once closed, you will
hear a single beep.
IMPORTANT: When the batteries are about to run out, the lock will beep four
times and will not close.
NORMAL OPENING
To open the lock, press button A on the remote control. Once open, you will hear
two beeps.
IMPORTANT: When the batteries are about to run out, the lock will beep fi ve
times when opened. The batteries must be changed to ensure it continues to
function correctly.
EMERGENCY OPENING:
In the event the lock doesn't work when you press button A on the remote control
(due to empty batteries), you must carry out an emergency opening. To do this,
press and hold button B on the remote control for 3-6 seconds and the lock will
open.
MANUAL OPENING OR USE OF THE LOCK AS A LATCH:
You can lock and unlock the bolts by turning the manual opening knob anti-
clockwise.
IMPORTANT: IF THE REMOTE CONTROL IS MISPLACED
For safety reasons, if a remote control is lost then all remotes should be deconfi gu-
red and the confi guration process should be repeated again. This way, the opening
code is modifi ed, preventing the misplaced remote from being able to open the
invisible lock.
DECONFIGURING REMOTE CONTROLS
To delete opening codes A from the remotes, press and hold registration button A
on the lock (for approximately 10 seconds) until you hear a long beep.
To delete opening codes B from the remotes, press and hold registration button B
on the lock (for approximately 10 seconds) until you hear a long beep.

CHANGING THE BATTERIES

When the lock' s batteries are running out, they will give off sound signals (see
the instructions in "Closing" and "Opening").
GED ONCE A YEAR TO ENSURE THE PRODUCT CONTINUES TO FUNCTION CO-
RRECTLY.
HOW TO CHANGE THE REMOTE CONTROL'S BATTERY (1 X CR2032 3V)
RECOMMENDATIONS
We recommend measuring the height at which the invisible lock is installed in
case the technical service needs to perform an emergency intervention. Measure
the distance from the ground to the bottom of the lock and memorise it (other
options: note it down on your mobile phone, tell a person you trust, etc.).
En
THE BATTERIES SHOULD BE CHAN-