Cable Installation - Milwaukee M18 2817-20 Manual Del Operador

To prevent damage to the cable and
NOTICE
attachments, only use in recommended
pipe size.
Remove the anchor cable packaging stop from the
front drum mount before use.
Selecting the Proper Cable
Cat. No.
48-53-2776 3/8" x 75' Inner Core
Coupling Cable
48-53-2777 3/8" x 100' Inner Core
Coupling Cable
48-53-2778 1/2" x 75' Inner Core
Coupling Cable
Cable Attachments for 3/8" and 1/2" Cables
Cat. No.
48-53-2786 Medium Funnel Head Attachment
w/ RUST GUARD™ Plating
48-53-2787 Medium Drop Head Attachment w/
RUST GUARD™ Plating
48-53-2788 1-1/2" Spade Bit Attachment w/
RUST GUARD™ Plating
48-53-2789 1-1/2" C-Cutter Attachment w/
RUST GUARD™ Plating

Cable Installation

To reduce the risk of injury, always
WARNING
wear proper eye protection marked
to comply with ANSI Z87.1.
Always wear leather gloves over latex/rubber
gloves to avoid entanglement. Cable tip may be
sharp. Never feed more than 100' of cable into the
machine to avoid overloading.
Remove the cable for cleaning after each use. Differ-
ent size and types of cables are available for different
applications. The instructions below detail how to
remove/install the cable manually.
To manually remove the cable:
1. Move the Forward/OFF/Reverse switch to OFF O
and remove the battery pack. Pull the cable out
through the nose of the drum until the anchor
cable shows.
2. Remove the cable from the anchor cable by insert-
ing the pin key into the coupling hole and pulling
the cable away.
3. To clean or maintain cable, follow the cleaning
instructions under "Maintenance".
Description
Diameter
1-1/2" - 3"
1-1/2" - 3"
3" - 4"
Description
To manually install the cable:
1. Move the Forward/OFF/Reverse switch to OFF O.
Ensure the cable feed is disengaged by pressing
down on the cable feed quick release button.
2. Attach the cable to the anchor cable by snapping
the attachment coupler into the cable coupler.
3. Move the Forward/OFF/Reverse switch to
Forward
Pipe
4. Use the foot pedal to start the drum.
5. Manually feed the cable into the drum. WARNING!
Always wear leather gloves over latex/rubber gloves
to avoid entanglement.
Cable Attachment Installation
To install the attachment:
Snap the attachment coupler into the cable coupler.
Test the cable before inserting into the drain to make
sure the attachment does not fall off during use.
To remove the attachment:
Insert the pin key into the coupling hole and pull at-
tachment off of cable.
Attaching Cable Drive Assembly
1. Align mounting plate to the Cable Drive™ Assembly
attachment holes and fasten using four screws with
a T-20 bit.
2. Attach Cable Drive™ Assembly to mounting plate
on the tool.
Cable Drive™ Assembly for M18™ Drum Machine
Sold separately. Refer to manual or Milwaukee Tool
website for the Cable Drive™ Assembly instructions.
1. Install wheel shaft through frame eyelet holes.
2. Attach wheels with recess facing out to wheel shaft.
3. Attach e-clip to the shaft groove using pliers to clamp
e-clip into place.
Make sure the handle is locked in the upright position
before transporting.
1. Pull back on the folding mechanism with one hand
while lifting the handle with the other hand.
2. Continue to lift handle to the upright position until
the folding mechanism clicks into place.
3. Reverse the process when storing the handle of
the tool.
Ensure handle is in the locked position before
transporting.
Do not use cart to transport other loads or add
additional product. For use with recommended
cable size/lengths only.
Always turn OFF O or remove battery from the
machine before transporting.
Ensure the foot pedal cord is properly wrapped
and the pedal is stored before transporting.
Always clear the area of obstructions before
transporting.
To roll cart from place to place, grasp the transport
handle and tilt the machine back onto the tires. Push,
don't pull, the machine.
1. Place the sewer drum machine no further than 2' from
the drain. WARNING! Greater distance can cause twist-
ing, kinking, breaking or whipping of the cable.
2. Remove the foot pedal from storage and unwrap
the cord and place to the side, ensuring the cord
will not tangle with the cable.
5
.
Wheel Installation
Using the Handle
Transportation
Drain Cleaning Setup