Protecting The Environment; Technical Data - Black and Decker MTIM3 Traducido De Las Instrucciones Originales

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 27
ENGLISH
Š Pull and hold the chuck collar (11) away from the front of
the tool.
Š Insert the bit shaft (12) into the chuck (10).
Š Release the collar. The accessory is locked in place.
Note! To remove the bit/socket repeat the above steps.
@
Use
Warning! Let the tool work at its own pace. Do not
overload.
Screwdriving / nut setting
Note: Ensure the forward reverse slider (2) is not in the locked
position.
Š Select the appropriate bit / socket for the screw or nut to
be driven.
Š Select forward or reverse rotation as described above.
Š Hold the tool in line with the fastener.
Š After tightening, check torque with a torque wrench.
Hints for optimum use
Screwdriving
Š Always use the correct type and size of screwdriver bit.
Š If screws are difficult to tighten, try applying a small
amount of washing liquid or soap as a lubricant.
Š Always hold the tool and screwdriver bit in a straight line
with the screw.
Maintenance
Your BLACK+DECKER tool has been designed to operate
over a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
@
regular cleaning.
Warning! Before performing any maintenance on
the tool, remove the battery from the tool. Unplug the
charger before cleaning it.
Š Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Š Regularly clean the motor housing using a damp cloth. Do
not use any abrasive or solvent-based cleaner.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Š Safely dispose of the old plug.
Š Connect the brown lead to the live terminal in the
new plug.
@
Š Connect the blue lead to the neutral terminal.
Warning! No connection is to be made to the earth
terminal. Follow the fitting instructions supplied with
good quality plugs.
Recommended fuse: 13 A.
6
(Original instructions)

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according
to local provisions. Further information is available at
www.2helpU.com

Technical data

No-load speed
min
-1
Beats
min
-1
Max. torque
Nm
(PTI Rating)
Chuck capacity
mm
Weight
kg
Level of sound pressure according to EN 62841:
Sound pressure (L
) 94.2 dB(A), uncertainty (K) 3 dB(A)
pA
Sound power (L
) 105.2 dB(A), uncertainty (K) 3 dB(A)
WA
Vibration total values (triax vector sum) according to EN 62841:
Screwdriving with impact (a
) 15.9 m/s
h, IS
EC Declaration of Conformity
%
Machinery Directive
MTIM3 Impact Wrench
Black & Decker declares that these products described under
"technical data" are in compliance with:
2006/42/EC, EN 62841-1:2015; EN 62841-2-2:2014;These prod-
ucts also comply with Directive 2014/30/EU and2011/65/EU.
For more information, please contact Black & Decker at the
following address or refer to the back of the manual.
MTIM3
MTIM3
(14.4v)(H1)
(Max)(H1)
0-2800
0-3000
0-3100
0-3500
170
205
6 (Hex)
6 (Hex)
1.3
1.3
, uncertainty (K) 1.5 m/s
2
2

Publicidad

Tabla de contenido
loading

Tabla de contenido