Technical Specifications - Metabo RSEV 17-125 Instrucciones De Manejo

Ocultar thumbs Ver también para RSEV 17-125:
Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

en
ENGLISH
Avoid inadvertent starts: always switch the
tool off when the plug is removed from the
mains socket or if there has been a power cut.
In continuous operation, the machine
continues running if it is forced out of your
hands. Therefore, always hold the machine with
both hands using the handles provided, stand
securely and concentrate.
Avoid the machine swirling up or taking in dust
and chips. After switching off the machine,
only place it down when the motor has come to a
standstill.
Switching on: push the slide switch (3) forwards.
For continuous operation, tilt it downwards
until it engages.
Switching off: press the rear end of the slide switch
(3) and release it.
8. Maintenance
Prior to each use, check if there are parts
missing, worn, broken, torn or damaged. Do not
use defective or incomplete guard.
Replace brush rim (21): replace worn brush rim
for optimum extraction.
See page 3, illustration F.
Pull out worn brush rim and fully insert new brush
tim (order no. 6.26733).
9. Cleaning
Cleaning the motor: It is possible
that particles deposit inside the
power tool during operation. This impairs the
cooling of the power tool. Conductive build-up can
impair the protective insulation of the power tool and
create an electrical hazard.
The power tool should be cleaned regularly, often
and thoroughly through all front and rear air vents
using a vacuum cleaner or by blowing in dry air.
Prior to this operation, separate the power tool from
the power source and wear protective glasses and
dust mask. Ensure appropriate suction is available
when blowing out vents.
10. Troubleshooting
The electronic signal indicator (5) lights
up and the load speed decreases. There is
too much load on the machine! Run the
machine in idling until the electronic signal indicator
switches off.
The machine does not start.The
electronic signal indicator (5) flashes.
Restart protection is active. If the mains plug is
inserted with the machine switched on or if the
power supply is restored following an interruption,
10
3
I
0
the machine does not start up. Switch the machine
off and back on again.
11. Accessories
Use only genuine Metabo accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
See www.metabo.com or the catalogue for a
complete range of accessories.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
A defective mains cable must be replaced only with
a special, original mains cable from metabo
available from the Metabo service.
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
The generated sanding dust may contain harmful
substances: dispose of appropriately.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
tools, packaging and accessories.

14. Technical Specifications

Explanatory notes regarding the specifications on
page 4. Subject to change in accordance with
technical progress.
Ø
= max. diameter of the accessory
t
= max. permitted thickness of clamping
max,1
shank on accessory when using
clamping nut (10)
M
= Spindle thread
l
= Length of the sanding spindle
n*
= No-load speed (maximum speed)
I
= Current at 120 V
120 V
P
= Rated input power
1
P
= Power output
2
m
= Weight without mains cable
* Energy-rich, high-frequency interference can
cause fluctuations in speed. The fluctuations
disappear, however, as soon as the interference
fades away.
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.

Publicidad

Tabla de contenido
loading

Tabla de contenido