Manuales relacionados para Truper DES-63
Resumen de contenidos para Truper DES-63
- Página 1 Manual Gas Brushcutter Applies for: Code Model 12671 DES-63 DES-63 63 cc Motor Read the user’s manual thoroughly CAUTION before operating this tool.
-
Página 2: Tabla De Contenido
Contents CAUTION Technical data Fuel Specifications To gain the best performance of the tool, prolong the duty life, General Motor Tool safety Warnings make the Warranty valid if necessary, and to avoid hazards Safety Warnings for Brushcutters of fatal injuries please read and understand this Manual before Parts using the tool. -
Página 3: Technical Data
Technical data DES-63 Code 12671 Description Gas Brushcutter Net Weight 22 lb Motor 63 cc Motor Rated Power 3 HP Fuel Tank 0.34 gal Speed 9000 RPM Cutting Capacity 17” Axis Length 59” Cutting Systems Nylon Thread Spool, Blades and Circular Saw (not included) Type of handle “Bicycle”... -
Página 4: General Motor Tool Safety Warnings
General Motor Tool safety Warnings Keep your work area clean, tidy and well lit. Wear adequate protective safety accessories. CAUTION CAUTION Cluttered and dark areas may cause accidents. Wear eye protection, dust mask, non-skid safety shoes, helmet and ear plugs. These safety gears reduce the risk Never use the tool in explosive areas or in the presence of injury. -
Página 5: Safety Warnings For Brushcutters
Safety Warnings for Brushcutters • In extreme weather confirm there is no ice forming and Fuel Handling condensation in the Gas Brushcutter. • Confirm the visibility and light conditions are adequate • Never smoke near fuel, or in the gas filling up zone or when preparing the oil mix, nor when operating the to be able to see clearly. -
Página 6: Parts
Parts Jack Line Cutting Thread Idle Screw Primer bulb Guard Apron Harness Fuel Tank Fuel Tank Ring Trigger Switch Release Control Straight Handle Axis Throttle Lock Throttle Trigger Straight Axis Auxiliary Handle Straight Axis Double Harness Quick Plastic release support system Apron Guard... -
Página 7: Assembly
Assembly Handle Guard • Separate the bracket from the straight axis mounting. • Secure the guard onto the Loosen the four bolts in the upper side. cutter head using the bracket • Set the handle in place fixing and tightening the bracket and bolts included. - Página 8 Assembly Harness • Set both suspenders over the shoulders. • Insert the left suspender plastic bushing (1) into the orifice of the right suspender. • Insert the side leash (2) into the plastic bushing. • Secure the system inserting the pin (3) in the plastic bushing.
-
Página 9: Fuel Filling Up
Fuel Filling Up Motor Fuel Supply • Follow the safety standards for handling fuel (page 5). • Allow the motor to cool down completely before supplying fuel. • Set the Gas Brushcutter into a flat surface. • Wipe clean around the fuel tank cap to prevent contamination. -
Página 10: Operation
Start Up Starting the Motor When Hot • Set the Gas Brushcutter on levelled ground using care the blade is not making contact with any obstacle. • Set the switch in the ON position (H). • Press and release the Primer bulb 10 times (I). •... -
Página 11: Maintenance
Maintenance • Before inspecting, cleaning or carrying out service to the Gas Brushcutter, turn off the motor. Wait until all the mobile parts stop. Disconnect the spark plug cable and separate it from the spark plug. Otherwise you could suffer severe injuries and / or damage to the tool. -
Página 12: Regular Maintenance
Maintenance Gas Brushcutter Storage In the event of storing the Gas Brushcutter for one month or longer, bear in mind the following considerations: • Drain all the fuel tank contents into an approved gasoline container. All the remaining fuel can be re-used in another tool that uses 2-stroke motor with a 50:1 ratio. -
Página 13: Authorized Service Centers
Authorized Service Centers In the event of any problem contacting a Truper Authorized Service Center, please see our webpage www.truper.com to get an updated list, or call our toll-free numbers 800 690-6990 or 800 018-7873 to get information about the nearest Service Center. -
Página 14: Warranty
. Transportation costs resulting from compliance of this warranty will be covered by For questions or comments, call 800-690-6990. Made in China. Imported by Truper S.A. de C.V. Parque Industrial 1, Parque Industrial Jilotepec, Jilotepec, Edo. de Méx. C.P. 54257 Stamp of the business.