Kichler 16193BKTNL Manual De Instrucciones

CAUTIONS
SAFETY INSTRUCTIONS
READ THIS FIRST
KEEP THESE INSTRUCTIONS
CAUTION – RISK OF SHOCK:
Disconnect Power at the main circuit breaker panel or main fusebox before
starting and during the installation.
WARNING:
This fixture is intended for installation in accordance with the National Electrical
Code (NEC) and all local code specifications. If you are not familiar with code
requirements, installation by a certified electrician is recommended. Failure
to adhere to these codes and instructions may result in serious injury and/or
property damage and will void the warranty.
CLEANING:
• Always be certain that electric current is turned off before cleaning.
• Only a soft damp cloth should be used. Harsh cleaning products may damage
the finish.
INSTRUCTIONS PERTAINING TO A RISK OF FIRE,OR INJURY TO PERSONS
IMPORTANT SAFETY INSTRUCTIONS
WARNING — To reduce the risk of FIRE OR INJURY TO PERSONS.
1. Turn off / unplug and allow to cool before replacing lamp.
2. Lamp gets HOT quickly! Contact only switch / plug when turning on.
3. Do not touch hot lens or cowl.
4. Do not remain in light if skin feels warm. (Light is intense, it may cause "sunburn".)
5. Do not look directly at lighted lamp.
6. Keep lamp away from materials that may burn.
7. Use only with wattage and lamp marked on fixture.
8. Do not touch the inner glass envelope of the lamp at any time. Use a soft cloth. Oil from skin may
damage lamp.
9. Do not operate the fixture with a damaged or missing lens.
1. WARNING: This fixture is not to be installed within 10 feet (3M) of a pool, spa or fountain.
2. This fixture is to be used only with a power unit (transformer) rated a maximum of 300 W (25
AMPS) 15 volts.
3. The unit low voltage cable shall:
a) be protected by routing in close proximity to the luminaire or fitting, or next to a building
structure such as a house or deck;
b) not be buried except for a maximum 6 inches (15.2 cm) in order to connect to the main low
voltage cable; and
c) have the length cut off so that it is connected to a connector within 6 inches (15.2 cm) from a
building structure, a luminaire, or fitting.
4. Direct burial rated wire is to be buried a minimum of 6" (152mm) beneath the surface of the ground.
NOTE: If additional Direct Burial wire is needed, contact your local Kichler® landscape distributor.
• 8 GA wire can be purchased in length of 250' (76 M), 15503-BK.
• 10 GA wire can be purchased in length of 250' (76 M), 15504-BK.
• 12 GA wire can be purchased in lengths of 100' (30 M), 15501-BK; 250' (76 M), 15502-BK; 500' (152M),
15505-BK; and 1000' (304 M), 15506-BK.
5. Fixture shall not use a tungsten halogen lamp unless the fixture is marked for use with such lamps.
6. Wiring connections must be made with approved/listed wire connection device(s) suitable for the
application. Do not exceed manufacturers' wiring combination specifications for size and quantity
of conductors.
WHEN INSTALLING KICHLER LANDSCAPE LIGHTING (LINE VOLTAGE OR
LOW VOLTAGE), CARE SHOULD BE TAKEN TO KEEP CLEAR OF POTENTIALLY
COMBUSTIBLE MATERIALS.
WHEN MAINTAINING THE FIXTURES, BE SURE TO REMOVE LEAVES,
PINE NEEDLES, GRASS CLIPPINGS, MULCH, OR ANY DEBRIS THAT HAS
ACCUMULATED ON THE LIGHT BULB, LENS, OR BODY OF THE FIXTURE.
INSTALLATION INSTRUCTIONS
1. TURN OFF POWER.
2. Determine desired location for mounting fixture.
3. At desired location, hammer stake into ground. To avoid damage to stake, place a board on top
of stake or use a rubber mallet. If ground is hard and stake is difficult to install, make a crosscut in
ground using a flat shovel.
4. Clear away area in ground at wireway opening in stake.
5. Unassemble cowl from fixture. Cowl is removed by loosening the thumb screw.
6. Install lamp (pure white lamp provided for 16193AZT and 16193BKT) to socket inside accent light.
NOTE: Use caution when installing. Hold lamp by outer housing. DO NOT touch glass envelope
inside. If this happens, clean lamp with denatured alcohol and a lint free cloth.
7. (Optional for 16193AZT and 16193BKT):
If additional beam spread is desired, place beam expander (textured lens) into cowl, dot side facing
outwards. Add amber lens inside the cowl if a warmer output is desired. If both beam expander
and amber lens are desired, first place beam expander into cowl, and then place amber lens.
With the beam expander and/or amber lens installed, place lens retainer into cowl. Make sure the
retainer is lying flat on the lens and is snug in the cowl.
NOTE: To ensure best performance of beam expander and/or amber lens, operate this fixture
with the lamp provided. Creating the desired lighting effect is dependent on using this fixture with
the lamp originally included.
8. Install cowl onto accent light housing and then tighten the thumb screw.
9. Route fixture cable through wireway opening and install fixture in stake. Care should be taken
to ensure wire is not twisted. Aim fixture in desired direction and secure by tightening locknut. If
necessary, use wrench or pliers for final tightening of nut.
10. Adjust angle of accent light by loosening swivel adjustment screw.
11. Make wire connections using supplied wire nuts following instructions on bag.
REV 4-APR-2022
Lighted lamp is HOT!
CAUTION
For warranty information please visit: kichler.com/warranty
FIXTURE DIAGRAM
FIXTURE
SWIVEL
ADJUSTMENT
SCREW
LOCKNUT
WIREWAY
OPENING
LENS RETAINER
STAKE
FCC INFORMATION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
866-558-5706
We're here to help
Hrs: M-F 9am to 5pm EST
LAMP
NOTE: DOT SIDE
FACES OUTWARD
AMBER LENS
BEAM EXPANDER
THUMB SCREW
COWL
IS-16193-US