Cleaning & Maintenance - Hendi 239278 Manual Del Usuario

Note: Using a pan or pot that's not suitable for induction cook-
GB
ing may damage the appliance.
Cleaning & maintenance
• ATTENTION! Always disconnect the appliance from the pow-
er supply and cool down before storage, cleaning & mainte-
nance.
• Do not use water jet or steam cleaner for cleaning and do not
push the appliance under the water as the parts will get wet
and electric shock might be resulted.
• If the appliance is not kept in a good state of cleanliness, this
can adversely affect the life of the appliance and result in a
dangerous situation.
• Food residues should be regularly cleaned and removed from
the appliance. If the appliance is not cleaned properly, it will
reduce its lifespan and may result in a dangerous condition
during use.
Cleaning
• Clean the cooled exterior surface with a cloth or sponge
slightly dampened with a mild soap solution.
• For reasons of hygiene, the appliance should be cleaned be-
fore and after use.
• Avoid water contacting the electrical components.
• Never immerse the appliance in water or other liquids.
• Never use aggressive cleaning agents, abrasive sponges, or
cleaning agents containing chlorine. Do not use steel wool,
metallic utensils, or any sharp or pointed objects for cleaning.
Do not use petrol or solvents!
Maintenance
• Check the operation of the appliance regularly to prevent se-
rious accidents.
• If you see that the appliance is not working properly or that
there is a problem, stop using it, switch it off and contact the
supplier.
• All maintenance, installation and repair work must be car-
ried out by specialised and authorised technicians, or recom-
mended by the manufacturer.
Transportation and Storage
• Before storage, always make sure that the appliance has
been disconnected from the power supply and completely
cooled down.
• Store the appliance in a cool, clean and dry place.
• Never place heavy objects on the appliance as this could
damage it.
• Do not move the appliance while it is under operation. Dis-
connect the appliance from power supply when moving and
hold it at the bottom.
Troubleshooting
If the appliance does not function properly, please check the
below table for the solution. If you are still unable to solve the
problem, please contact the supplier/service provider.
8
Problems Possible cause
The appliance does - Power plug is
not switch ON. not connected
properly with the
electrical outlet.
- On/Standby (1)
button is not
pressed.
Cooling fan is - This is normal.
operating even The cooling
after the appliance fan continues
is switched to running in
Standby mode. Standby mode for
some time to cool
down all internal
elements.
Error code identification
Error Possible cause
codes
E 1 The temperature of the
appliance is too high
Cooling fan defective
E 2 The pan or pot is
overheated.
Possibly, the pan
becomes empty and
appliance will shut
down for protection.
E 3 The supply voltage
is abnormal. (Supply
voltage is too high or
too low)
Warranty
Any defect affecting the functionality of the appliance which
becomes apparent within one year after purchase will be re-
paired by free repair or replacement provided the appliance has
been used and maintained in accordance with the instructions
and has not been abused or misused in any way. Your statutory
rights are not affected. If the appliance is claimed under war-
ranty, state where and when it was purchased and include proof
of purchase (e.g. receipt).
In line with our policy of continuous product development we
reserve the right to change the product, packaging and docu-
mentation specifications without notice.
Discarding & Environment
When decommissioning the appliance, the prod-
uct must not be disposed of with other household
waste. Instead, it is your responsibility to dispose
to your waste equipment by handing it over to a
designated collection point. Failure to follow this
rule may be penalized in accordance with applicable regula-
tions on waste disposal. The separate collection and recycling
of your waste equipment at the time of disposal will help con-
Possible solution
- Check the power
plug to make
sure it is con-
nected properly.
- Press the On/
Standby (1)
button to start
operation.
- Wait until the
cooling fan stops
rotating.
Possible solution
Clear all obstacles that
around the appliance.
Unplug the appliance,
remove the pan or pot,
wait until the appliance
is completely cool down.
Contact the supplier.
Unplug the appliance,
remove the pan or pot,
wait until the appliance
is completely cool down.
And make sure water is
inside the pan.
Make sure that the
appliance is connected
to a suitable electrical
power supply.