Black+Decker ASI500 Manual De Instrucciones página 24

24 • ENGLISH
To use your inflator immediately you can do so without
setting the automatic shut-off feature.
f Switch the main power switch (1) to the inflate position
(c, Fig. H).
f To switch between the different units (PSI, BAR or
KPA) press - & + buttons (21 and 23) together until
the required units are displayed.
f Connect the universal valve adaptor (6) and an
accessory, if required, to the item to be inflated,
making sure that the lever (19) of the valve adaptor
is in the down position to lock it in place.
Note: Make sure that the universal valve adaptor is
correctly fitted to the item to be inflated.
f To start the inflator press the power button (22) on
the LCD.
f When the item is inflated as required or to stop the
inflator at any time press the power button (22)
on the LCD.
f Remove the hose from the item and store it on the
unit.
f Turn the main power switch (1) to the off position
(b, Fig. H).
Setting the Automatic Shut-off Pressure
(Fig. H and I)
Note: The LCD will only show inflation pressures when the
inflator is being used. In both inflation and pump mode the
unit will show battery status.
f To switch between the different units (psi, bar or kPa),
press - & + buttons (21 and 23) at the same time until
the required units are displayed.
f Press and hold either buttons - & + (21 and 23)
for 3 seconds until the display flashes.
f While the display is flashing press the - or + (21 and 23)
until the required pressure is displayed.
f After 3 seconds the display will flash and return to a
reading of "0.0". This is normal.
f Connect the universal valve adaptor and accessories,
if required, to the item to be inflated, making sure that
the lever of the valve adaptor is in the down position to
lock it in place.
f To start the inflator press the power button (22) on
the LCD.
f When the item to be inflated has reached the preset
value the unit will automatically turn off.
Note: You may notice the actual pressure reading
may drop after a couple of seconds, this is normal.
f To stop the inflator at any time press the power button
(22) on the LCD.
f Remove the valve adaptor or accessory from the
inflated item and the 12 Volt adapter (8) from your
vehicle's 12 Volt accessory socket.
f Turn the main power switch (1) to the off position (b).
Note: If the main power switch is turned off, all
settings will be lost and will need to be re-entered
following the instructions under the heading "Setting
the automatic shut-off pressure". This is a safety
feature to prevent the risk of items "Over Inflating".
Using the Inflator as a Pressure Gauge
f Switch the main power switch (1) to the inflate position
(c, Fig. H).
f Connect the universal valve adaptor (6) to the item
to be checked.
f The LCD will display the items pressure.
f After checking, turn the main power switch (1) off
and return the air hose to the storage location.
Operating the High-Volume Pump
Note: Do not operate the pump when the vehicle's engine
is running.
Note: Make sure that your 12 Vdc accessory socket is live.
On some vehicles the accessory socket may only become
live when the ignition key is in the accessory position.
To inflate using the high-volume pump (i.e air mattresses,
rafts, swimming pool floats):
Note: The pump mode DOES NOT have an auto
shut-off feature.
f Switch the main power switch (1) to the pump position
(a, Fig. H).
f Remove the high-volume hose (7) from the storage
channel around the center of the unit and connect it
to the high-volume pump inflate connection (10).
f Insert the hose (with accessories if required) to the
item to be inflated.
f To start the pump press the power switch (22) on
the LCD.
f When the item is inflated as required or to stop the
pump at any time press the power switch (22) on
the LCD.
f Remove the hose from the item and store it
on the unit.
f Turn the main power switch (1) to the off position
(b, Fig. H).
To deflate using the high-volume pump (i.e air mattresses,
rafts, swimming pool floats):
Note: The pump mode DOES NOT have an auto
shut-off feature.
f Switch the main power switch (1) to the pump position
(a, Fig. H).
f Remove the high-volume hose (7) from the storage
channel around the center of the unit and connect it
to the high-volume pump deflate connection (4) (Fig. I).
f Insert the hose (with accessories if required) into the
item to be deflated.