Publicidad
GB
1. Assembly of the rear wheels
Place the body with the underside facing up. Place the gearbox (2) on the rear axle. Now attach
a drive wheel (3) to the gear unit. Slide a washer (6) onto the rear axle. Fix the whole thing with
a lock nut (9). Tighten the nut with a spanner. Finally, put a cover (10) on the wheel. Repeat this
on the other side.
2. Assembly of the front wheels
To mount the front wheels, slide a washer (6) onto the front axle. Attach a wheel (4) including
bearing bush (5) and slide a washer (6) onto the axle. Fix the whole thing with a lock nut (9).
Tighten the nut with a spanner. Finally, attach a cover (10). Repeat the steps to mount the other
wheel.
3. Gearbox connection
Pay attention to the installation direction when installing the gear units (L = left, R = right),
connect the gearbox connections to the connections in the model. The choice of connection
has no effect on the direction of rotation of the gear units. Only connect connectors that fit into
each other.
Battery connection
Connect all connectors as shown. Only plug matching connectors into eachother and be sure
not to reverse the polarity. Make sure the red wire is well connected with the red terminal on the
battery, and same as the black one.
4. Steering wheel assembly
Open the battery cover. Put 2 AA batteries making sure that it is corectly put in. Then close the
cover. Install the steering wheel (14) in the Intended position and secure it with the Safety pin
(15) and nut (16)
Battery warning:
Non-rechargeable batteries are not to be recharged!
Do not open! Do not dispose of in fire! Do not mix old and new batteries!
Do not mix alkaline batteries, standard (carbon-zinc) or rechargeable batteries!
Rechargeable batteries are to be removed from the toy before being charged!
Rechargeable batteries are only to be charged under adult supervision!
The supply terminals are not to be short-circuited!
5. Attach the Motor Hood
Fit the Motor hood (7) on the motor. Tighten four screws (8) to secure it. Reapeat the abouve
for the other motor hood.
6. Attach Seat
Position the seat (12) over the vehicle body. Tighten two screws (11) with a screwdriver.
7. Attach the Windshield
Insert the tabs on the windshield (17) in the slots on the vehicle body, push until you hear it click
into place.
3
5
Problem
The battery can no longer be charged
The battery can no longer be charged although the battery and charger
are OK.
The journey time is very short.
No function
Can be switched on but does not drive.
Can be switched on but does notmove, or only direction.
Can be switched on but only travels in one direction
The active fuse blows and switches the unit off for a few seconds. You will
hear a single click at the beginning
No sound function on the steering wheel/andlebar
Vehicle has very high wear on switches.
The rubber tyres come loose on the wheels
8 8
4
2
1
Source
Carger or battery defective.
Charging socket defective
The battery has been deep discharged or is worn out.
Battery is not or incorrectly connected.
ON/OFF switch defective.
Motor cable incorrectly connected or not connected.
Gas or direction switch defective.
Directional switch defective.
Oberload or electrical short circuit.
Battery is dead.
Dirt and moisture damage the switches.
Ridden on too hot a surface or in dirt.
8. Attach the view mirrors
Install wing mirror (13) to the designated position, and fasten it.
9. Charging Your Vehicle
• The power swich must be turned in OFF position when charging.
• Insert the charger (16) into the socket - the LED lights up green. Connect the charger to
the charging socket on the dashboard.
• The LED on your charger lights up red as long as the battery is being charged. If the LED
lights green again, the battery is fully charged.
• The charge time is 10 hours.
• Do not charge the battery more than once within 24 hours.
• Charger and battery heat up during the charging process.
Attention!
•
The charger is not a toy. Only use the charger supplied.
•
The battery may only be charged by or under the supervision of an adult.
•
The terminals must not be short-circuited.
•
The charger must be checked regularly for damage to the cable, plug, housing and other
parts. If any damage is found, the charger must not be used until the damage has been
repaired.
• Let the model cool ovv sufficiently after each use before putting it back into operation.
When using an additional batteries let it cool off for minimum 15 minutes until the model
is operated again. Overheating can damage the electronics or may result in fire.
•
Always disconnect the battery from the charger immediately after charging. Always
disconnect the charger from the power supply immediately after disconnecting the
battery. Inserting the rechargeable battery or charger after charging will result in
damage to the battery, charger or the power supply (fire hazard).
•
Use the charger only in dry rooms.
Functions
1
ON/Off switch
With the ON/OFF switch you start the vehicle.
2
Shift Lever
Forward:
Press the "Forward-backward switch" on the "Forward" position.
Press the "Foot pedal", the model drives forward.
Reverse:
Press the "Forward-backward switch" on the "Backward" position.
Press the "Foot pedal", the model drives backward.
IMPORTANT!
Always stop vehicle when changing the direction to avoid damage the
gears and motor.
3
Sounds buttons
4
Speed
High speed - Fast speed
Low speed - Slow speed
5
Foot pedal
To move the car, press the pedal down.
To brake or slow down, release pressure from the pedal.
Solution
Check charger and battery
Check or replace the charging socket.
Use a new battery and avoid deep discharge.
Connect the battery (see instructions)
Check or replace switch.
Check and connect motor cable (see instructions).
Check or replace switch.
Check or replace switch.
Do not overload or have the until checked.
Replace battery.
Do not drive in moisture or dirt such as meadows, gavel, sand, etc.
Change tyres and avoid hot surfaces and dirt.
Publicidad
