General Warnings - Bellman & Symfon BE1441 Manual De Instrucciones

Power LED indications
When the flash receiver is connected to mains power, the power LED lights up in green. The
BE1442 model is also equipped with battery backup and the power LED indicates the following:
Power LED Status
Green light The flash receiver is connected to mains power.

The backup batteries are detected.
The flash receiver is connected to mains power.
 Green blinks
No backup batteries are detected.
Red light The flash receiver is running on battery backup.

 Red blinks The backup batteries are nearly depleted.
Personalizing your receiver
Directing the flash
The flash receiver features a rotating top that makes it easy to direct the light. Point it for example
towards a wall if you feel that the flash is too intense. A silicone slip-on top is also available in a
variety of colors (art. no. BE9164-BE9167).
Changing the radio key
If your Visit system is activated for no reason, there is probably a nearby system that triggers yours.
In order to avoid radio interference, you need to change the radio key on all units. The radio key
switches are located on the transmitters.
1 Open the transmitter cover and move any radio key switch to the up (on position) to change
Changing the radio key
the radio key. See
2 Press and hold the test button located on the top of the flash receiver until the green and
yellow Visit LEDs blink alternately. Release the button.
3 Press the test button/s on the transmitter within 30 seconds to send the new radio key.
4 All Visit LEDs on the receiver blink 5 times to show that the radio key has been changed. Please
note that all Visit units must be set to the same radio key.
1 2
22
for the relevant transmitter.
3
5

General warnings

This section contains important information about safety, handling and operating conditions.
Keep this booklet for future use. If you are just installing the device, this booklet must be given to
the householder.
Hazard warnings
 Failure to follow these safety instructions could result in fire, electric shock, or other injury or
damage to the device or other property.
Keep this device out of reach of children under 3 years.

 Be aware that alarms and notifications can be missed if batteries run out.
Do not use or store this device near any heat sources such as naked flames, radiators, ovens or

other devices that produce heat.
 Flashes can trigger epileptic seizures for people with photosensitive epilepsy (PSE).
Use only power adapters and battery types that are specified in this booklet.

Protect cables from any potential source of damage.

 Do not dismantle the device; there is a risk of electric shock. Tampering with or dismantling the
device will void warranty.
This device is designed for indoor use only. Do not expose the device to moisture.

 Protect the device from shocks during storage and transport.
Do not make any changes or modifications to this device. Use only original Bellman & Symfon

accessories to avoid any electrical shock.
 Batteries are toxic. Do not swallow them! Keep out of reach of children and pets. If they are
swallowed, consult your physician immediately!
Information on product safety
 Failure to follow these instructions could result in damage to the device and void the warranty.
Do not expose batteries to fire or to direct sunlight.

 Rechargeable batteries should be charged fully before using the device for the first time. Only
charge batteries in a temperature between 0°– 35°C, 32°– 95° F.
 Rechargeable batteries should only be changed by Bellman & Symfon or an authorized service
center. There is a risk of explosion if the batteries are not replaced correctly.
 Do not drop your device. Dropping onto a hard surface can damage it
Do not use the device in areas where electronic equipment is prohibited.

4
The device may only be repaired by an authorized service center.

 If a serious incident occurs in relation to this device, contact the manufacturer and relevant authority.
If you encounter other problems with your device, contact the point of purchase, your local

Bellman & Symfon office or the manufacturer. Visit
The programming pin on the back of the flash receiver is for authorized service personnel only.

Unauthorized use may damage the device.
Without permission granted by the NCC, no company, enterprise or user is allowed to

change the frequency, enhance the transmitting power or alter the original characteristics or
performance on an approved low power radio frequency device.
 This device should not be used on aircrafts unless specifically permitted by flight personnel.
bellman.com for contact info.
EN
23