PROZIS Satin Manual Del Usuario página 6

EN
The unit will start working once the "I" and the triangle markings are aligned. After use, switch
off the device by rotating the bottom housing, aligning the triangle with the "O" marking.
Shaving:
1. Attach the shaver head.
2. Twist the bottom housing to the right and align the "I" and the triangle markings to start the unit.
3. Hold the shaving foil against the skin, moving the shaver slowly and smoothly in circular
motions against your natural hair growth.
4. Don't press the device too hard against the skin as this will cause irritation and may damage
the foil.
5. Since your skin may be sensitive after shaving, test your moisturizer on a small patch of skin
and wait to see if any irritation occurs.
6. Clean the shaver after each use to ensure a long-lasting performance.
7. Twist the bottom housing to the left and align the "O" with the triangle marking to switch off
the unit.
Using the bikini trimmer:
1. Start with the guide comb attached for first-time use.
2. Switch on the device.
3. To fully remove hair or to outline the bikini area, use the trimmer without the attachment comb.
4. While removing the hair, gently move the blades against your natural hair growth.
5. To outline, place the blades perpendicular to the skin and apply the blades to the edge of
the hair. Use the blades to create the desired shape.
6. For a clean finish, follow up with the foil shaver.
7. For cutting hair without completely removing it, attach the detail comb to the head. Place
the comb over the cutting blades first, align the comb ribs with the top surface of the
trimmer's head housing and then snap it into place on the back of the trimmer.
8. Remove the guide comb to release it from the trimmer's head.
Using the eyebrow trimmer:
10
1. This trimmer comes with two trimming blades. The larger blade can be used to trim body
hair and eyebrows. The smaller blade is ideal for detailing. It also comes with a comb
attachment that helps you achieve an even cut when you do not want to fully remove the
hair. The comb attachment has two sides: the long tooth is for body hair, and the short
tooth is for eyebrow trimming.
2. Aligning the indicator with the 6 mm marking on the comb leaves hair longer, while align-
ing it with the 3 mm marking leaves the hair shorter.
3. To use the comb attachment, make sure the unit is switched OFF and slide the comb over
the trimming blades. Make sure the comb's teeth are facing in the same direction as the
trimming blade, and that the top of the comb is even with the top of the trimmer. If you
want to fully remove hair, use the trimmer without the comb attachment.
4. To operate the trimmer, twist the bottom housing to the right, pointing the arrow towards
the "I" marking. After trimming, switch off the device by twisting the bottom housing to the
left, pointing the arrow to the "O" marking.
5. To store the trimmer, slide the comb attachment cover over the trimming blades.
Using the facial brush head:
1. Make sure the unit is switched off.
2. Twist the head to the right aligning the triangles.
3. Change the accessory and fit a new one, then twist it to the left and align the "0" with the
triangle marking.
4. Add a drop of facial cleanser to the head of the brush and moisten it under the tap or shower.
5. Twist the bottom housing to the right and align the "I" and the triangle markings to start the unit.
6. Divide your face into 4 main sections for deep cleansing: forehead, nose and chin, left
cheek, and right cheek.
7. While applying gentle pressure, move the roller brush in circular motions over each sec-
tion for approximately 30 seconds.
Troubleshooting
Some issues that arise may be solved by the user. If the problem persists after having tried
the following solutions, please contact Prozis customer service.
PROBLEM
The device is not working.
SOLUTION
Make sure the power cord is plugged in / Make sure the
battery is properly placed in the battery compartment. Test the
battery to make sure it is working / Check the blades to see if
they are clogged with any hair residue. If so, use the cleaning
brush to remove it.
EN
11