Tabla de contenido
Publicidad
Idiomas disponibles
Idiomas disponibles
OPERATION
WARNING
Keep your arms and face away from being directly above the
cooking area when operating the appliance.
1
2
3
Item
Icon
1
Light for Oven
2
Oven Control Knob
3
Left Cooktop Control Knob
4
Middle Cooktop Control Knob
5
Right Cooktop Control Knob
6
Light for Cooktop Control Knob
Lighting Instructions
NOTE: This range is equipped with a flame detection device on
each cooktop burner and the oven burner. During the lighting
process, ensure that the knob is held in for 5-10 seconds to heat up
the thermocouple. If not held in long enough, the flame detection
device will stop gas flow to the burner.
Operating the Cooktop Burners
1.
Before lighting, reset gas control knobs
to the OFF position.
2.
Check that the main inlet gas valve is OPEN.
3.
Push and turn the gas control knob
counterclockwise to
position
until burner lights. (You will hear
clicking sound when the knob is pushed in.)
4.
If ignition does not occur in 5 seconds, turn gas control knob
off, wait 5 minutes and repeat the lighting procedure.
5.
Once the burner flame is lit, continue to hold the cooktop
control knob in for 5-10 seconds, then release knob and verify
the cooktop burner stays lit. Repeat the above steps if the
cooktop burner flame goes out after releasing the control
knob.
6.
After the cooktop burner flame is ignited and the control knob
is released, then turn the control knob counter-clockwise to
the
desired
burner flame setting.
7.
Verify visually that the cooktop burner has ignited once the
control knob has been set to the desired setting. The burner
flame should ignite within a few seconds.
8.
To turn off the cooktop burner, rotate the cooktop knob
clockwise to the off position.
4
5
6
Description
Operating the Oven
1.
Before lighting, reset gas control knobs
to the OFF position.
2.
Check that the main inlet gas valve is OPEN.
3.
Keep the oven door in the open
position for the full ignition process
view the pilot and that the oven burner has lit.
4.
Push and turn the gas control knob counterclockwise to the
position until pilot lights. (You will hear a clicking sound when
the knob is pushed in.)
5.
If ignition does not occur in 5 seconds, turn gas control knob
off, wait 5 minutes and repeat the lighting procedure.
6.
Once the pilot flame is lit, continue to hold the oven control
knob in for 5-10 seconds, then release the knob and verify the
pilot flame stays lit. Repeat the above steps if the pilot flame
goes out after releasing the knob. (Keep the oven door open
for this process)
7.
After the pilot flame is ignited and the control knob is released,
then turn the control knob counter-clockwise to the required
temperature setting.
8.
Verify visually that the oven burner has ignited once the
control knob has been set to the desired temperate. The
burner flame should ignite within a few seconds.
9.
After verifying the burner has ignited, please close the oven
door to continue the preheat process.
10. To turn off the oven burner, rotate the oven control knob
clockwise to the off position. Ensure the burner flame and the
pilot flame have extinguished.
If the burner does not ignite
In the event of failure to light the burner within 5 seconds,
immediately turn the control knob clockwise to the OFF position.
Wait at least 5 minutes and repeat the igniting procedure. If ignition
still not occur, use a gas lighter or a match to light the burner. Refer
to the 'Manual Ignition' section.
Manual Ignition
Use care when lighting the burners by hand. If a burner lights unexpectedly,
or your hand is to close to the burner, you could be burned.
In the event of failure to ignite the burner in standard ignition, you may
light the burner manually by following the steps below:
a
1.
Push in and turn the appropriate burner
control knob counterclockwise to the
2.
Immediately strike and place a burning long wooden
match or a gas lighter near the burner of cooktop
1
(
) or pilot of oven (
1
3.
Once the burner flame or pilot frame is lit, continue to hold the control
knob in for 5-10 seconds, then release knob and verify the frame
stays lit. Repeat the above steps if the flame goes out after releasing
the control knob.
4.
Repeat steps 1 to 3 to light the other burner(s) as required.
5.
Rotate the burner control knob to adjust the flame to desired level.
- 10 -
WARNING
position.
2
2
a and
b) to light.
Remove the
diffuser tray
2
a
CCD-0005506 Rev: 08-16-22
to
2
b
Publicidad
Tabla de contenido
Solución de problemas
