Eu-Konformitätserklärung; Scope Of Delivery; Operating Elements - Goobay 60418 Instrucciones De Uso

DE | EN Betriebsanleitung | User Manual
LED-Trafo | LED Transformer
2. Schrauben Sie mit einem Kreuzschlitzschraubendreher die Abdeckungen von Primär- und Sekun-
därseite ab und legen Sie die Abdeckungen samt Schrauben beiseite.
3. Bereiten Sie die Anschlusskabel für den Anschluss an den Klemmblöcken vor, indem Sie ca.
6 mm von der Isolierung an den Kabelenden entfernen.
4. Schließen Sie Ihre LEDs in richtiger Polarität an die Klemmböcke im Sekundärstromkreis (SEC)
an.
Um die Gesamtleistung (P in Watt) Ihrer Leuchtmittelkombination zu errechnen, multipliziert man
die Stromaufnahme des Leuchtmittels (I in Ampere) mit dessen Spannung (U in Volt). Dabei gilt
P=U*I. In Parallelschaltungen bleibt die Spannung (U) konstant. In Reihenschaltungen bleibt die
Stromstärke (I) konstant.
5. Wenn alle Verbraucher sekundärseitig richtig angeschlossen sind, schließen Sie die Primärseite
(PRI) über die Klemmböcke N und L an das Stromnetz an.
6. Prüfen Sie die Funktion aller installierten Komponenten, bevor Sie den LED-Trafo in Berieb neh-
men.
7. Setzen Sie die Abdeckungen wieder ein und schrauben Sie diese fest.
8. Befestigen Sie den LED-Trafo mit Hilfe von Schrauben an den Befestigungsschlitzen.
Beachten Sie dabei den Mindestabstand von 50 mm in alle Richtungen.
6 Verhalten im Störfall
Bei Störungen wie Überlast, Übertemperatur oder Kurzschluss löst ein interner Sicherheitsmechanis-
mus aus und die Stromversorgung zum Sekundärstromkreis wird unterbrochen. Nachdem die Störung
beseitigt wurde, arbeitet der LED-Trafo wieder normal weiter.
7 Wartung, Pflege, Lagerung und Transport
Das Produkt ist wartungsfrei.
ACHTUNG! Sachschäden
• Reinigen Sie das Produkt nur, wenn es vom Stromkreis abgetrennt ist.
• Verwenden Sie zum Reinigen nur ein trockenes und weiches Tuch.
• Verwenden Sie keine Reinigungsmittel und Chemikalien.
• Lagern Sie das Produkt bei längerem Nichtgebrauch für Kinder und Tiere unzugänglich und in tro-
ckener und staubgeschützter Umgebung.
• Lagern Sie das Produkt kühl und trocken.
• Lagern Sie das Produkt nicht in der Nähe von leicht entzündlichen Gegenständen.
• Heben Sie die Originalverpackung für den Transport auf.
8 Entsorgungshinweise
Elektrische und elektronische Geräte dürfen nach der europäischen WEEE Richtlinie nicht mit
dem Hausmüll entsorgt werden. Deren Bestandteile müssen getrennt der Wiederverwertung
oder Entsorgung zugeführt werden, weil giftige und gefährliche Bestandteile bei unsachgemä-
ßer Entsorgung die Gesundheit und Umwelt nachhaltig schädigen können.
Sie sind als Verbraucher nach dem Elektrogesetz (ElektroG) verpflichtet, elektrische und elektronische
Geräte am Ende ihrer Lebensdauer an den Hersteller, die Verkaufsstelle oder an dafür eingerichtete, öf-
fentliche Sammelstellen kostenlos zurückzugeben. Einzelheiten dazu regelt das jeweilige Landesrecht.
Das Symbol auf dem Produkt, der Betriebsanleitung und/oder der Verpackung weist auf diese Bestim-
mungen hin. Mit dieser Art der Stofftrennung, Verwertung und Entsorgung von Altgeräten leisten Sie
einen wichtigen Beitrag zum Schutz unserer Umwelt.
WEEE Nr.: 82898622
9 EU-Konformitätserklärung
Mit dem CE-Zeichen erklärt Goobay®, eine registrierte Marke der Wentronic GmbH, dass
das Produkt die grundlegenden Anforderungen und Richtlinien der europäischen
Bestimmungen erfüllt.
Weitere Informationen finden Sie auf unserer Webseite unter der Artikelnummer:
https://www.wentronic.com/
1 Safety instructions
The user manual is part of the product and contains important information for correct use.
• Read the user manual completely and carefully before use.
The user manual must be available for uncertainties and passing the product.
• Keep this user manual.
Risk of life by electric shock!
Working on the electrical mains and improper installation can result in serious injury or death.
• Installation, disassembly, maintenance and repair work must be carried out only by trained elect-
rical specialists.
REV2022-05-02
V1.0aw
Änderungen und Irrtümer vorbehalten. │ Subject to change without notice.
• Before working on the product or on electrical mains, disconnect the product from the power sup-
ply, switch off the fuse and secure the fuse against being switched on again.
• Observe the enclosed VDE installation notes.
• In commercial facilities, always observe the accident prevention regulations of the German Emp-
loyer's Liability Insurance Association for electrical systems and equipment.
• Only put the product into operation when all components have been properly installed and che-
cked for functionality.
• Do not open the housing.
• Do not modify product and accessories.
• Do not short-circuit connectors and circuits.
• Do not overload the product.
• Observe the maximum permissible power.
Due to the reactive power that often occurs with LED lamps, always choose transformers with an ap-
prox. 40-50 % stronger power.
• Only use the product with LED lamps.
• Do not connect a dimmer to the product.
The product can be damaged by a dimmer.
• Also observe the safety and operating instructions of the other devices that are to be connected
to this product.
Heat storage
• Ensure that the air supply is not obstructed and that the product is not covered at any time.
• Keep a minimum distance of 50 mm in all directions around the transformer (See Fig. 3).
Do not operate a device if it is not in working order. In such cases, it must be secured against uninten-
tional further use.
• Use product, product parts and accessories only in perfect condition.
• Avoid stresses such as heat and cold, moisture and direct sunlight, microwaves, vibrations and
mechanical pressure.
• In case of questions, defects, mechanical damage, trouble and other problems, non-recoverable
by the documentation, contact your dealer or producer.
Not meant for children. The product is not a toy!
• Secure packaging, small parts and insulation against accidental use.
• Keep the product away from animals.
2 Description and function
2.1 Product
The product is a voltage transformer that converts mains voltage into constant low voltage and is used
as a direct current source for LEDs. Due to the constant output voltage, the transformer is primarily sui-
table for parallel circuits. The flat design enables space-saving installation and thanks to the integrated
protection electronics, the transformer is also approved for installation in furniture.
2.2

Scope of delivery

LED Transformer, User Manual
2.3

Operating Elements

See Fig. 1.
1 Primary side with cover (mains connection) 3 Terminal blocks
2 Secondary side with cover (connection for 4 Mounting slots
LED lighting)
3 Intended use
We do not permit using the device in other ways like described in chapter „Description and
Function" or in the „Safety Instructions". Use the product only in dry interior rooms. Never
use the product in rooms where there are flammable gases or vapours. Not attending to
these regulations and safety instructions might cause fatal accidents, injuries, and
damages to persons and property.
IP20: This product is protected against medium sized foreign objects, but not against water ingress.
4 Preparation
1. Check the scope of delivery for completeness and integrity.
2. Compare the specifications of all used devices and ensure compatibility.
5 Installation
NOTICE! Material damage
• Always connect the secondary circuit first before connecting the primary circuit.
• Assign the N/L and plus and minus terminal blocks as marked on the product.
• The cable on the secondary side to the LED lighting should not be longer than 2 m to comply with
the EMC directive.
• Do not exceed the loads specified in the „Specifications" section.
- 2 -
60418, 60419, 30004, 30618
• Maintain a minimum distance of 50 mm in all directions around the transformer (See Fig. 3).
See Fig. 2
1. Check whether the fuse is switched off and secured against being switched on again and check
with a voltage tester whether the cables to be wired are really voltage-free.
2. Unscrew the covers of the primary and secondary sides with a Phillips screwdriver and put the co-
vers and screws aside.
3. Prepare the connecting cables for connection to the terminal blocks by removing approx. 6 mm of
the insulation from the cable ends.
4. Connect your LEDs in correct polarity to the terminal blocks in the secondary circuit (SEC).
To calculate the total power (P in watts) of your lamp combination, multiply the current consumpti-
on of the lamp (I in amperes) by its voltage (U in volts). P=U*I applies here. In parallel circuits, the
voltage (U) remains constant. In series circuits, the current (I) remains constant.
5. When all consumers are correctly connected on the secondary side, connect the primary side
(PRI) to the mains via the terminal blocks N and L.
6. Check the function of all installed components before operating the LED transformer.
7. Replace the covers and screw them tight.
8. Secure the LED transformer using screws at the mounting slots.
Observe the minimum distance of 50 mm in all directions.
6 Response to faults
In the event of faults such as overload, overtemperature or short circuit, an internal safety mechanism
is triggered and the power supply to the secondary circuit is interrupted. After the cause of the fault has
been eliminated, the LED transformer continues to operate normally.
7 Maintenance, Care, Storage and Transportation
The product is maintenance-free.
NOTICE! Material damage
• Only clean the product when it is disconnected from the power supply.
• Only use a dry and soft cloth for cleaning.
• Do not use detergents or chemicals.
• When not in use for a long time, store the product out of reach of children and animals and in a
dry and dust-protected environment.
• Store cool and dry.
• Do not store the product near easily inflammable objects.
• Keep and use the original packaging for transport.
8 Disposal instructions
According to the European WEEE directive, electrical and electronic equipment must not be
disposed with consumers waste. Its components must be recycled or disposed apart from each
other. Otherwise contaminative and hazardous substances can damage the health and pollute
the environment.
As a consumer, you are committed by law to dispose electrical and electronic devices to the
producer, the dealer, or public collecting points at the end of the devices lifetime for free. Particulars are
regulated in national right. The symbol on the product, in the user manual, or at the packaging alludes
to these terms. With this kind of waste separation, application, and waste disposal of used devices you
achieve an important share to environmental protection.
WEEE No: 82898622
9 EU Declaration of conformity
With the CE sign Goobay®, a registered trademark of the Wentronic GmbH ensures, that
the product is conformed to the basic European standards and directives.
You can find more information on our website by searching for the item number:
https://www.wentronic.com/en/
by Wentronic GmbH | Pillmannstraße 12
38112 Braunschweig | Germany
Goobay®