Ec Declaration Of Conformity - Annovi Reverberi AR Spray 16 Traduccion De Las Instrucciones

10
English
the constant temperature operation of the product and extend the working time and service life of the battery, avoid using it when the battery surface is hot.
8.3 Filters and valve cleaning
Keep always filters clean. Clean inlet filter (A2) after every use. If the fluid flow seems reduced, please unscrew the nut at the base of the gun (A16),
and clean the gun filter (A15) with fresh water (fig. 8). Also, open the cap (A1) and check the pump filter (A4) placed at the bottom of the tank body (A3),
and clean it with fresh water (fig. 9). If the tank tends to vacuum clean the cap valve (A1B) with fresh water.
9 TRANSPORT AND STORAGE (PAGE 41)
Warning - danger!
All installation and assembly operations must be performed with the appliance disconnected from the battery. Store the accessories as shown in fig. 10. Transport
the machine as shown in fig. 11. After finishing work, clean the appliance and disassemble the accessories; store them on the hook (A14, fig. 12). Take care to not
to damage the appliance during transport. Store it on a flat and stable surface (fig. 13). Empty the appliance in case of transport and storage. Store the appliance
in a dry place and do not never leave it outdoor. Protect it from freezing.
10 TROUBLESHOOTING
Problem
The appliance does not switch on
EN
The battery does not charge
The appliance stops while working
The pumps is under pressure but the
liquid does not come out
The tank tends to vacuum:
We, Annovi Reverberi S.p.A, of Bomporto (Modena), Italy, declare that the following Annovi Reverberi appliance(s):
Designation of appliance: Sprayer
Model No.:
Rated power:
is (are) compliant with the following European directives:
2006/42/EC, 2009/127/EC, 2014/35/EU, 2014/30/EU, 2011/65/EU, 2015/863/EU
and was (were) produced in compliance with the following norms or standardised documents:
EN 19932-1, EN 19932-2, EN 12100, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3, EN 62233, EN 50581.
Name and address of the person responsible for issuing the technical file: Stefano Reverberi / AR Managing Director
Via ML King, 3 - 41122 Modena, Italy
Date: 01.08.2020
MODENA (I)
Stefano Reverberi
95902_KK_Manual_AR_sprayer_INNER.indb 10 95902_KK_Manual_AR_sprayer_INNER.indb 10
Possible causes
Battery empty
Battery not correctly inserted in the appliance housing
The battery has overheated and the internal auto reset
protection has cut in
Appliance or battery faulty
Charger not correctly connected to the battery
Battery charger or battery not ready for charging. Battery
overheated.
Battery charger or battery faulty
Battery empty
The battery has overheated and the internal auto reset
protection has cut in
Filters or lance nozzle are clogged
Filters fouled or not correctly fitted
Tank empty
Cap valve is clogged

EC Declaration of conformity

AR SPRAY 16
18 W
Managing Director
(Original instructions)
Remedy
Fully charge the battery
Take out the battery and insert it correctly
Wait for the battery to cool down
Replace the battery and/or contact an authorised service centre
Take out the charger and insert it correctly
Wait for the battery to cool down
Replace the charger and battery and/or contact an authorised
service centre
Fully charge the battery
Wait for the battery to cool down
Check and clean the nozzle or the filters
Clean filters / Fit filters correctly
Fill the tank
Remove the valve from the cap and clean it
2021/2/1 下午12:25 2021/2/1 下午12:25