Refrigerator Installation; Unpacking; Installation; Closing And Aligning The Doors - LG LTN16385PL Manual De Usuario

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

WARNING
EXCESSIVE WEIGHT HAZARD
Use the assistance of two or more persons to move or
install the refrigerator. Not following these instructions
may cause injury to the back and other parts of the
body.

UNPACKING

Before installing your refrigerator, remove any tape
or temporary stickers. Do not remove any stickers
that feature warnings, the model serial number or the
technical label of the product located on the back of the
refrigerator.
To remove adhesive tape residue, rub it well with your
fingers and a little liquid detergent. Clean with warm
water and let dry.
Do not use sharp instruments, rubbing alcohol, flammable
liquids or abrasive cleaning products to remove the
adhesive tape or glue. These products can damage the
surface of your refrigerator. For more information, see
the section "Important Safety Instructions".
The shelves come already installed in their factory
position. Remove the shelves and replace them
according to your spacing needs.
Moving Your Refrigerator:
Your refrigerator is extremely
heavy. Make sure you protect
the floor when moving your
refrigerator for cleaning or
servicing. Always pull your
refrigerator straight out when
moving it. Do not shift from side to side or "walk"
the refrigerator when attempting to move it as this
can cause damage to the floor.
WARNING
EXPLOSION HAZARD
Keep all flammable materials and vapors (such as
gasoline) away from the refrigerator. Not following
these instructions may cause death, explosion or fire.

INSTALLATION

1. Avoid placing the unit near heat sources, direct
sunlight, or humidity.
2. To avoid vibration, the unit should be leveled. If needed,
adjust the leveling screws to compensate for an
unleveled floor. The front should be slightly taller than
the rear to ensure that the doors close properly. The
leveling screws can easily be turned by slightly tilting
the front of the refrigerator, turning the leveling screws
clockwise (
) to raise it and counter-clockwise
(
) to lower it.

REFRIGERATOR INSTALLATION

3. Install the refrigerator in an area between 50 °F (10 °C)
ONCE INSTALLED
1. Carefully clean your refrigerator and remove and dust
2. Install accessories such as the ice tray, door
3. Leave your refrigerator on for 2 to 3 hours before
• Take care when working with the hinges, base cover
• DO not place your hands or any tools in the air vents,
KEEP A PROPER DISTANCE FROM
ADJACENT OBJECTS
Please keep the refrigerator at an
adequate distance from other objects.
Insufficient spacing can reduce the
refrigerator's freezing efficiency and
increase electricity consumption.

CLOSING AND ALIGNING THE DOORS

Your refrigerator has two front leveling screws, one on
the right and one on the left. If your refrigerator seems
unstable or if you would like the doors to close more
easily, simply adjust the inclination of the refrigerator by
following the instructions below:
1. Plug the refrigerator into a 3 prong grounded
7
and 109,4 °F (43 °C). If the surrounding temperature
is lower or higher than previously mentioned, it can
adversely affect the unit.
CAUTION:
Avoid placing the unit near heat
sources, direct sunlight or humidity.
accumulated during shipping.
compartments, shelves, etc., in their proper places.
These are already packed to prevent any possible
damage during shipping.
storing food inside. Verify that there is a flow of cold air
in the freezer compartment to ensure proper cooling.
Your refrigerator is now ready for use.
WARNING:
and stops, etc. You may injure yourself.
the base cover or in the bottom of the refrigerator. This
may cause injury or electrical shock.
outlet. Move the refrigerator into its final position.
(5.08 cm) 2"
Figure A

Publicidad

Capítulos

Tabla de contenido
loading

Tabla de contenido