Technical Characteristics - AVE TS-SMART7ALS Manual Del Usuario

ENG
TS-SMART7ALS • TS-SMART7ANS
7" Touch Screen video intercom monitor - IP Range
1) OVERVIEW
TS-SMART7ALS and TS-SMART7ANS are displays featuring a 7"LCD touch screen with the following
functions:
• audio-video indoor station for the AVE V44 SMART video intercom system;
• Graphic touch screen for home automation system management
Avoid installation in places subject to sudden changes in temperature and humidity and in places
with a lot of dust (in combination with a supervisor equipped with a web server);
• Graphic touch screen for SMART 44 system management
• Touch screen for the management of the anti-intrusion system with control units of the AF927 range;
• External IP camera viewer;
The device is supplied with active "SMART HOME", "ANTI-THEFT" and "VIDEO INTERCOM" functions;
when configuring the system, we recommend deactivating any unnecessary functions by accessing the
"Settings/Advanced parameters/Main page management" menu.
The graphical user interface allows managing various functions in a simple and user-friendly manner:
• Management of lights, dimmers, blinds, temperature control, etc... belonging to the AVE Domina
Plus home automation system (in combination with a device with integrated web-server);
• Anti-intrusion control unit remote panel
(activation/deactivation/partial setting/reset of alarms);
• IP camera monitoring through RSTP protocol
(contact the toll-free number 800 015 072 for compatible camera models);
• Intercom calls within the same apartment or between different apartments;
• Acquisition of the image from the outdoor station upon receipt of a call;
• Screensaver with digital frame;
• Video intercom system control
The device is equipped with wireless LAN connection and Wi-Fi:
• The wired connection must be used to connect the indoor station with the video intercom outdoor
station. The wired connection can be used to interface the device with the data network to which
the home automation web server or the anti-intrusion control units are connected only if the TS-
SMART7xx device is used for managing the home automation and/or anti-intrusion system (and
there is no connection to the external video intercom station on the system)
• The Wi-Fi connection must be used to interface the device with the data network to which the
home automation web server or the anti-intrusion control unit is connected.
Warnings
See the "Installation requirements" section at www.ave.it under the TECHNICAL MANUALS section.
We recommend arranging an internet connection to allow remote support service in case of need and a
dedicated power supply line (UPS).
We also recommend periodically checking for software updates in order to enjoy the best performance
and ensure proper operation. Updates are available via the technical support network.
2) REFERENCE REGULATIONS
For performance
• EN 62820-1-2:2017 Building intercom systems - Part 1-2: System requirements –
Building intercom systems using the Internet Protocol (IP).
They also comply with the following directives and regulations:
• Directive 2014/53/EU (RED) (only where applicable): The full text of the EU declaration of conformity
is available at the following Internet address: www.ave.it
• RoHS Directive 2011/65/EU;
• REACh Regulation (EC) No. 1907/2006; The manufacturer, AVE SPA, declares that the radio
equipment complies with Directive 2014/53/EU. The full text of the EU declaration of conformity is
available at the following Internet address: www.ave.it.
3) DIMENSIONS
220 mm
4) INSTALLATION
Install the product about 1.5m from the ground (see figure below); fix the wall mounting bracket (supplied)
on a 3-module box installed horizontally. Hook the touch screen to the wall mounting bracket and slide
it down slightly to secure it. When installing the product, keep in mind the following indications: Do not
block or obstruct the vents and openings in the product. Avoid installation in places subject to sudden
changes in temperature and humidity and in places with a lot of dust. In addition, keep the product away
from direct sunlight, from sources of bright light (which compromise the good visibility of the LCD display)
or from heat sources.
Caution:
The vertical axis of the internal position is shifted to the left by 10 mm with respect to the vertical axis of
the box installed in the wall.
5) DISPLAY
6) CONFIGURATION
The device is supplied pre-programmed for installation within a single-button system; changes can be
made by accessing the "Settings/Advanced Parameters" menu (default password 222222) or by using
the appropriate software available from the product page on the website www.ave.it. (from which the
complete installation guide is available for downloading).
For the full configuration of the product, download the complete product manual using the QR
code shown on the last page of this document.
7) OUTSIDE DOOR BELL BUTTON
The product connector features the Z8 input for the connection of the N.O. button of the outside door bell:
27 mm
the connection can be made using a 2x0.50 mm
power and sections not exceeding 20 m).
To date, the other inputs of the connector are not in use.
TS-SMART7ANS
24 V 350mA
AVE S.p.A.
Via Mazzini, 75
25086 REZZATO (BS) - Italy
Made in China
POWER PoE 48V

8) TECHNICAL CHARACTERISTICS

10 mm
2
a) Silencing: button for silencing the ringtone of the device.
b) Wi-Fi: access to the ON/OFF/Wi-Fi configuration menu of the device.
c) Display: access to the parameter configuration menu of the display. From this menu it is possible to:
• Set the brightness of the screen;
• Choose the screen saver image or upload an image from an SD card
(not supplied with the product);
• Set the time after which the screensaver is activated;
• Set the turn-off time of the LCD of the device;
• Activate the lock screen with password function. Note: the parameter enables the "Lock
screen" function present in the drop-down menu of the home page
(default password 666666).
d) Cleaning: button to inhibit the touch screen of the device.
The touch screen becomes active again after 30 seconds.
e) Screen lock: button for activating the screen lock.
f) Restart: button to restart the device
g) Settings: button for accessing the product settings menu.
a b c
Z8
GND
Power supply
Current consumption at rest
Current consumption in operation
Weight
Display
Protection rating
Data connection
Operating temperatures
SD card
d e f g
2 cable (we recommend using ducts separated from the
N.A.
Power supply +24V
CC
or
PoE 48V
DC
200 mA@ 24V
DC
260 mA@ 48V
DC
350 mA@ 24V
DC
180 mA@ 48V
DC
580 g
7" touch screen display - 1024 x 600 pixels
IP20 (IP30 installed)
RJ45 or Wi-Fi card (integrated)
5 °C – 45 °C
2 to 32 GB