Makita HR2631F Manual De Instrucciones página 11

Hold the ring and turn the sleeve counterclockwise to
open the chuck jaws. Place the bit in the chuck as far as
it will go. Hold the ring firmly and turn the sleeve
clockwise to tighten the chuck.
To remove the bit, hold the ring and turn the sleeve
counterclockwise. (Fig. 37)
Diamond core drilling
CAUTION:
• If performing diamond core drilling operations using
"rotation with hammering" action, the diamond core bit
may be damaged.
When performing diamond core drilling operations,
always set the change lever to the m position to use
"rotation only" action.
Operation when using the dust cup (optional
accessory) (Fig. 38)
Operate the tool with the dust cup against the ceiling
surface.
NOTE:
• The dust cup (optional accessory) is intended only for
drilling in the ceramic workpiece such as concrete and
mortar. Do not use the tool with the dust cup when
drilling in metal or similar. Using the dust cup for drilling
in the metal may damage the dust cup due to the heat
produced by small metal dust or similar.
• Empty the dust cup before removing a drill bit.
• When using the dust cup, make sure that the dust cap
is mounted on it securely.
MAINTENANCE
CAUTION:
• Always be sure that the tool is switched off and
unplugged before attempting to perform inspection or
maintenance.
• Never use gasoline, benzine, thinner, alcohol or the
like. Discoloration, deformation or cracks may result.
To maintain product SAFETY and RELIABILITY, repairs,
carbon brush inspection and replacement, any other
maintenance or adjustment should be performed by
Makita Authorized Service Centers, always using Makita
replacement parts.
OPTIONAL ACCESSORIES
CAUTION:
• These accessories or attachments are recommended
for use with your Makita tool specified in this manual.
The use of any other accessories or attachments might
present a risk of injury to persons. Only use accessory
or attachment for its stated purpose.
If you need any assistance for more details regarding
these accessories, ask your local Makita Service Center.
• SDS-Plus Carbide-tipped bits
• Core bit
• Bull point
• Diamond core bit
• Cold chisel
• Scaling chisel
• Grooving chisel
• Drill chuck assembly
• Drill chuck S13
• Chuck adapter
• Chuck key S13
• Bit grease
• Side grip
• Depth gauge
• Blow-out bulb
• Dust cup
• Safety goggles
• Plastic carrying case
• Keyless drill chuck
NOTE
• Some items in the list may be included in the tool
package as standard accessories. They may differ from
country to country.
Noise
The typical A-weighted noise level determined according
to EN62841-2-6:
Model HR2631F
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Model HR2631FT
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
Model HR2641, HR2320T, HR2630, HR2630T
Sound pressure level (L
Sound power level (L
Uncertainty (K): 3 dB (A)
NOTE:
• The declared noise emission value(s) has been
measured in accordance with a standard test method
and may be used for comparing one tool with another.
• The declared noise emission value(s) may also be
used in a preliminary assessment of exposure.
WARNING:
• Wear ear protection.
• The noise emission during actual use of the power
tool can differ from
depending on the ways in which the tool is used
especially what kind of workpiece is processed.
• Be sure to identify safety measures to protect the
operator that are based on an estimation of
exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as
the times when the tool is switched off and when it
is running idle in addition to the trigger time).
Vibration
The vibration total value (tri-axial vector sum) determined
according to EN62841-2-6:
Model HR2631F
Work mode: hammer drilling into concrete
Vibration emission (a
Uncertainty (K): 1.5 m/s
Work mode: chiselling function with side grip
Vibration emission (a
Uncertainty (K): 1.5 m/s
Model HR2631FT
Work mode: hammer drilling into concrete
Vibration emission (a
Uncertainty (K): 1.5 m/s
ENG905-1
): 92 dB (A)
pA
): 103 dB (A)
WA
): 91 dB (A)
pA
): 102 dB (A)
WA
): 90 dB (A)
pA
): 101 dB (A)
WA
ENG907-1
the declared value(s)
ENG900-1
2
): 12.4 m/s
h, HD
2
2
): 9.2 m/s
h, Cheq
2
2
): 11.6 m/s
h, HD
2
11