Metabo NFR 18 LTX 90 BL Manual Original página 21

f
10. Maintenance and inspection
CAUTION! Before performing any
maintenance or inspection, always remove
the battery pack and all nails.
Inspection of the magazine
Remove battery pack (9).
Clean the magazine. Remove any dust and wood
chips that have accumulated in the magazine.
CAUTION! Check if the feed slide (14) glides
smoothly by pulling it with your finger. If this is
not the case, the nails can exit at an unusual angle
and injure someone.
Clean the trigger safety lock (2) and maintain
smooth running.
Inspection of the fixing screws
Regularly inspect all fixing screws and ensure that
they are properly tightened.
If any of the screws become loose, tighten them
again immediately. Failure to do so could lead to
serious danger.
Exterior cleaning
If the tool is dirty, wipe with a soft dry cloth or a cloth
moistened with soapy water. Do not use chlorine
solvent, petrol or paint thinner as these soften
plastics.
f
11. Accessories
Use only original Metabo or CAS (Cordless Alliance
System) battery packs and accessories.
Use only accessories that fulfil the requirements
and specifications listed in these operating
instructions.
Chargers: ASC 145, etc.
Battery packs with different capacities. Buy
battery packs only with voltage suitable for your
power tool.
4.0 Ah (LiHD), order no.: 625367000
5.5 Ah (LiHD), order no.: 625368000
etc.
5.2 Ah (Li-Ion), order no.: 625028000
etc.
For a complete range of accessories, see
www.metabo.com or the catalogue.
12. Repairs
Repairs to electrical tools must ONLY be
carried out by qualified electricians!
Contact your local Metabo representative if you
have Metabo power tools requiring repairs. For
addresses see www.metabo.com.
You can download a list of spare parts from
www.metabo.com.
13. Environmental Protection
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.
Packaging materials must be disposed of according
to their labelling in accordance with municipal
guidelines. Further information can be found at
www.metabo.com in the "Service" section.
Battery packs may not be disposed of with regular
waste. Return faulty or used battery packs to your
Metabo dealer!
Do not allow battery packs to come into contact with
water!
Only for EU countries: never dispose of
power tools in your household waste!
According to European Directive 2012/19/EU
on Waste from Electric and Electronic Equipment
and implementation in national law, used power
tools must be collected separately and recycled in
an environmentally-friendly manner.
Discharge the battery pack in the power tool before
disposal. Prevent the contacts from short-circuiting
(e.g. by protecting them with adhesive tape).
f
14. Technical Data
Explanatory notes on the specifications on page 3.
Subject to change in accordance with technical
progress.
U = Voltage of battery pack
N = Suitable nails: head diameter
D
N = Suitable nails: diameter
d
N = Suitable nails: length
L
N = nail strips angle
W
N = Nail capacity (pieces)
A
Z = Cycle (nails per second)
m = Weight with smallest battery pack
Measured values determined in conformity with
EN 62841.
Permitted ambient temperature during operation:
0 °C (-4°F) to 40 °C (120°F) (limited performance
with temperatures below 0 °C (32°F)). Permitted
ambient temperature for storage: 0 °C (32°F) to 30
°C (86°F).
Recommended ambient temperature when
charging: 0 °C to 40 °C
direct current
The technical specifications quoted are subject to
tolerances (in compliance with relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. The actual load may be higher
or lower depending on operating conditions, the
condition of the power tool or the accessories used.
Please allow for breaks and periods when the load
is lower for assessment purposes. Arrange
protective measures for the user, such as
organisational measures based on the adjusted
estimates.
ENGLISH en
21