Publicidad
Idiomas disponibles
Idiomas disponibles
3. QUICK START GUIDE
MFPP-C1 must be connected to AC power to enable any feature of
the machine.
This manual describes the potential specifications of the MFPP-C1.
Only the functions with operational steps described in this section
are currently supported. The available functions depend on the
printer model or version. For more information, contact Canon
service.
A. Bypass Mode:
This operation will allow paper to pass through the MFPP-C1
without being punched.
This is the default mode of operation for MFPP-C1. MFPP-C1
will operate in Bypass mode when no punch option is selected.
B. Punch Modes: When a punch die is inserted
To configure the Die Set for the desired sheet size that is being
processed see section 8 – Die Set User Manual.
i) Single Punch Mode:
This operation will punch the trail edge of all sheets that pass
through the MFPP-C1. A properly configured die set must be
inserted before running single punch mode. See section 4. A for
details on Die set changes and follow the labels on the die set for
configuration. Select Single Punch on the printer job setup menu.
ii) Double Punch Mode:
This operation will punch two rows of holes- One in the middle
of the sheet and the other adjacent to the trail edge of all sheets
that pass through the MFPP-C1. A properly configured die set
must be inserted before running punch mode. See section 4. A for
details on Die set changes and follow the labels on the die set for
configuration. Select Double Punch on the printer job setup menu.
iii) Saddle Punch Mode:
This operation will punch the two rows of holes- One just before
the center of the sheet and the other the same distance after the
center of the sheet. A properly configured die set must be inserted
before running punch mode. See section 4. A for details on Die
set changes and follow the labels on the die set for configuration.
Select Double Punch on the printer job setup menu. Select Saddle
Punch on the settings menu of MFPP-C1.
C. Crease Modes: When a Crease die is inserted
i) Center Crease Mode:
This operation will apply a crease in the center of all the sheets that
pass through the MFPP-C1. The crease die set must be inserted
before running center crease mode. Select Center Crease from the
Settings menu on MFPP-C1.
ii) Book Crease Mode:
This operation will apply 2 creases around the center of all the
sheets that pass through the MFPP-C1. These crease positions
can be adjusted to increase the width of the book spine and its
position from the center. The crease die set must be inserted before
running book crease mode. Select Book Crease from the Settings
menu on MFPP-C1.
iii) C-Fold Crease Mode:
This operation will apply 2 creases spaced at 1/3 and 2/3 from the
trail edge of the sheet. These crease positions can be adjusted to
ensure the sheet will lay flat when folded. The crease die set must
be inserted before running C-Fold crease mode. Select C-Fold
Crease from the settings menu on MFPP-C1.
D.When a Perforation die is inserted
i) Single Perforation Mode:
This operation will apply a perforation, at the trail edge of all LEF
sheets & between the center and trail edge of all SEF sheets, that
pass through the MFPP-C1. A perforation die set must be inserted
before running single perforation mode.
MFPP-C1 will now function in Single Perforation mode.
ii) Center Perforation Mode
This operation will apply a perforation at the center of the all
thesheets that pass through the MFPP-C1. A perforation die set
must be inserted before running single perforation mode. MFPP-C1
will now function in Center Perforation mode.
iii) Double Perforation Mode
This operation will apply 2 perforations from the center of the sheet
to the trail edge, depending on sheet size and adjustment, on all
the sheets that pass through the MFPP-C1. The perforation die set
must be inserted before running single perforation mode. MFPP-C1
will now function in Double Perforation mode.
MFPP-C1
GB
5
Publicidad
