TDS HELIOS 6000 Manual página 2

Switch mode：(Wide / Spot / Red / Blue)
(On-State) Pressing the Switch Button for 1.5 second.
Wide Light Spot light
Colar light (blue+ red)
Adjustment brightness：(Wide/Spot / Red / Blue)
(On-State) Pressing the Switch Button for less than 1 second.
100%
25%
Gear adjustment：Colar light(Blue+Red)
(On-State) Pressing the Switch Button for less than 1 second.
Color 1
Color 4
Turbo light mode
(25％ Wide light state) Pressing the Switch Button for
1.5 seconds turn to the turbo light mode.
(On-turbo light mode) Pressing the Switch Button for
1.5 seconds return to the 25％ wide light state.
Turn On SOS：
(OFF- State) Pressing the Switch Button for 3 seconds
Turn OFF SOS：
(SOS- State) Pressing the Switch Button for 3 seconds.
General Maintenance
There two-rings in the tail cap. Use silicone to keep the
O-rings well lubricated. It is important to lubricate the
o-rings if the flashlight has not been used in a long time or
if the o-ring is hard. If the O-ring is damaged, broken or
deformed it should be replaced with the spare.
Note：Do not use a sharp tool to remove the O-rings.
Warning
1.Do not open the tail cap when the video light is in the water.
2.Do not shine the light directly into your eyes or another
person's eyes.
3.Do not touch the battery and charger with wet hands.
4.Use only the manufacturer's battery and charger with this
system.
5.If the video light will not be used for a long period of time the
battery should be removed.
Failure to comply with these warning may result in damage
to the video light and will nullify the warranty.
Red light
Blue light
75%
50%
Color 2 Color 3
Color 5
Switch mode：(SOS / Flash explosion)
(SOS- State) Pressing the Switch Button for less than 1 second.
SOS
Battery Level Indicator
Blue Light: Battery level is 100% - 80%;
Green Light: Battery level is 80% - 30%;
Red Light: Battery level is 30% - 5%;
Flash red Light: Battery level is < 5%.
Caution：When the battery level indicator is flash red.
1. Unable to switch the mode and adjust the brightness;
2. Only 20% brightness output;
3. Auto shutdown after 10 minutes .
To Charge the battery
1. Insert the plug of the DC charger into the battery (as shown
in the battery installation illustration).
2. Plug the charger into the power outlet. When the battery
starts to charge, the charger's indicator light will turn red.
3. When the battery is fully charged, the indicator light on the
charger will turn green.
4. Be sure to charge the first charge up to 100% capacity.
Automatic Overheat Protection
When being used at a temperature higher than 50°C ,
the light will automatically reduce the brightness by
20% to reduce heat and protect the components.
Warranty
We offer a warranty against manufacturing defects for three
years from the date of purchase. All manufacturing defects
occurring within three years from the date of purchase will be
repaired free of charge. Proof of purchase is required for
warranty support.
The warranty does not cover failures or defects resulting from
misuse (e.g., modifications or damage), natural disasters,
problems with the charger or battery, including improper
battery installation.
Troubles Shooting
Before returing the video light to the vendor, please try the
following to improve function.
Symptom
Check the battery to make sure
that it is inserted in the correct
The video light
direction
does not work
Check the battery is charged
Check the tail cap is tight
Check the battery to make sure
Indicator light is
that it is inserted into the charger
green when the
in the correct direction and that
battery begins
the battery has good contact with
charging
the charging terminal.
Check the O Rings in the tail
cap to make sure that they are
Internal Leakage
not broken and that there is no
Water
debris which might
Flash explosion
Solution