Publicidad
Idiomas disponibles
Idiomas disponibles
EN
Digital instructions
Locomotive are fitted with ESU's latest generation LokPilot® decoder version V.5.0. These new
decoders can be used in DCC digital systems.
YOUR BENEFITS:
• Factory preset address for the locomotive is 03.
• 40 khz tact frequency for smooth and silent motor control, 5th generation of load
control.
• The V.5.0 decoder supports DCC.
• 14, 28 or 128 selectable speed steps for DCC systems.
• Improved function mapping: All outputs can be assigned to any function button.
• Function outputs have a throughput of up to 250mA each, all outputs together 500mA.
• ABC braking mode: Stop in front of the signal.
DECODER PARAMETERS ADJUSTING:
The LokPilot V.5.0 decoder controls several parameters. You can find a list of the most
important ones at the end of this instructions. Each parameter (CV) can be configured
independently using its respective command.
When programming using Lenz, Uhlenbrock or Arnold equipment, please
refer to their programing instructions. If the error message "err02" is
displayed during programming with Lenz or Arnold equipment, a 47
Ohmresistor (0.5) Watt or higher) must be inserted between one of the
two supply cables and the programming track.
CV
NAME
1
Loco address
2
Start voltage
3
Acceleration
4
Deceleration
5
Maximum speed
6
Medium speed
8
Product ID
17 - 18
Extended locomotive address
27
Brake mode
28
RailCom® Configuration
29
Configuration register
Manufactured by:
Hornby Hobbies Ltd
Westwood, Margate,
Kent, CT9 4JX, UK
EU Authorised Representative:
Hornby Italia SRL
Viale dei Caduti, 52/A6,
www.hornbyinternational.com
Castel Mella (BS), Italy, 25030
Resistance 47
Central unit
Programming track
DESCRIPTION
Locomotive address
Sets the minimum speed of the engine
This value multiplied by 0.869 is the time from stop to maximum speed
This value multiplied by 0.869 is the time from maximum speed to stop
Maximum speed of engine
Averall engine speed
ESU version number
To lengthen locomotive address
Allowed brake modes
Bit
Function
0
ABC braking, voltage higher on the right hand side
1
ABC braking, voltage higher on the left hand side
2
ZIMO® HLU brakes active
3
Brake on DC, if polary against driving direction
4
Brake on DC, wenn polarität gleich wie Fahrtrichtung
Settings for RailCom®
Bit
Function
Channel 1 Address broadcast disabled
0
Channel 1 Address broadcast enabled
No data transmission allowed on Channel 2
1
Data transmission allowed on Channel 2
Automatic loco recognition disabled
7
Automatic loco recognition enabled
The most complex CV within the DCC standards. This register contains important information,
which is only relevant in DCC mode
Bit
Function
Normal direction of travel
0
Forward becomes reverse
14 speed steps (only in DCC mode)
1
28 or 128 speed steps (only in DCC mode)
Analogue mode off
2
Analogue mode permitted
Disable RailCom®
3
Enable RailCom®
Speed curve through CV 2, 5, 6
4
Speed curve through CV 67 - 96V
Short addresses (CV 1) in DCC-mode
5
Long addresses (CV 17+18) in DCC-mode
+49 8921094551
+34 938004786
DE
ES
customerservices.de@hornby.com
customerservices.es@hornby.com
technicalservices.de@hornby.com
technicalservices.es@hornby.com
+33 170807487
+44 (0)1843 233525
FR
UK
customerservices.fr@hornby.com
customerservices.uk@hornby.com
technicalservices.fr@hornby.com
technicalservices.uk@hornby.com
Ferrobús RENFE
DCC Systems (Lenz, Intellibox, etc.)
It is much easier to modify the parameters if you have a DCC compatible digital system or
an Intellibox. Please, read the corresponding chapter in your system manual (DCC decoders
programming). The V.5.0 LokPilot decoder support any NMRA programming system.
ANALOG OPERATION
When using conventional transformer, the locomotive movement will be similar to that of
a locomotive without a decoder. The locomotive will only start its running when receiving
a minimum voltage between 5.5 and 6 volts, as the decoder will not work with a lower
tension.
Please note the following warnings:
Always disconnect the decoder from the power supply before doing any work on it.
The reset function is very convenient, as you can set the original factory values again at any
time. To use this function, type "8" in CV 8 or "08" in register "08".
Functions
Main light
F0
Red lights
F2
Dimmer
F4
Issued Sept 2021 - AG - Subject to technical modifications
F1
Upper light
F3
Interior light
F5
Acceleration/deceleration on/off
RANGER
VALUE
1-255
1-255
1-255
1-255
128-9999
Value
1
2
4
8
16
Value
0
1
0
2
0
128
Value
0
1
0
2
0
4
0
8
0
16
0
32
14+
Service Sheet ELBD-147u
3
3
22
22
255
88
151
192
0
24
131
30
Publicidad
