Outside Living Industries ubbink MultiBright 20 Manual De Instrucciones página 8

1
Operating instructions for MultiBright Solar Float 20/25/30
Dear customer,
This operating manual contains important information on commissioning and use. Read the operating manual carefully before using the LED lamp. This applies particularly to the safety advice. Otherwise, you may
injure yourself or damage the LED lamp. Keep the operating manual for future use. If you pass the LED lamp on to a third party, be sure to hand over this operating manual as well. These operating instructions can
also be downloaded as a PDF file from our website www.outsideliving.com.
Safety instructions
This device may be used by children from the age of 8 and upwards and also by people with physical, sensory or mental disabilities or lacking suitable knowledge and experience, provided they are supervised or
have been instructed in the use of the device and understand the resulting hazards.
The LED lamp is intended for private use only and is not suitable for commercial applications. Only use the LED lamp as described in this operating manual. Any other use is considered improper and can lead to
damage to property and/or personal injury. The LED lamp is not a toy. The manufacturer or dealer accepts no liability for damage resulting from improper or incorrect use.
Check the LED lamp and scope of delivery
Risk of damage
If you open the packaging carelessly with a sharp knife or other pointed object, the LED lamp may be damaged. Take the LED lamp out of the packaging. Check if there is any damage to the LED lamp or remote
control. If this is the case, contact the dealer immediately.
Assembly
1. Take the LED lamp out of the packaging carefully. Remove the plastic card on the back of the remote control.
2. Place the LED lamp in a place where it can reach a full 8 hours of sunshine so that the rechargeable battery can reach its maximum capacity.
3. You can choose to place the LED lamp on land or on the water.
- For installation on land, mount the ground anchor at the intended location below the LED lamp and insert it together with the LED lamp into the ground.
Commissioning
To switch on the light, press and hold the ON/OFF switch on the bottom of the LED lamp for
approx. 2 seconds.
To adjust the colour or effect, briefly press the on/off button on the remote control. Please refer to
the following description for information on the individual effects and settings
In daylight, the LED lamp switches off automatically and charges the battery by itself. As soon as
dusk falls or night falls, the LED light detects this and switches on again automatically.
Periods out of use
If you do not use the LED lamp for a longer period of time, either let it stay in the water or lift the LED
lamp out of the water and store it in a dry and frost-proof place.
Maintenance and care
Cleaning the housing
Only use water and a soft cloth. Be careful not to apply too much pressure to the housing, otherwise it may be damaged. Clean the housing from time to time, or when dust or dirt has accumulated, to maintain the
full performance of the solar panel.
Replacement of illuminants
The replacement of individual, defective LED diodes is not possible. The affected device must be disposed completely.
Repairs
If the housing, LED strip or solar module are damaged, a repair is not possible. You may not continue using the affected part and it must be correctly disposed.
Troubleshooting
Do not repair the LED lamp yourself! If you use unsuitable parts for the repair, the risk of an electrical short circuit can increase greatly. Some problems may be caused by minor faults that you can fix yourself. To do
this, follow the instructions below according to the problem in question.
If this does not solve the problem, please contact the customer service department and keep the required information at hand according to the item "Ordering spare parts".
Problem
The LED lamp does not react
Not all colours are detected
Colours are only faint
Ordering spare parts
When ordering spare parts, or in the course of troubleshooting according to the item "Troubleshooting", we require the following information:
Cause
Battery drained
Remote control battery drained
Remote control too far away
Water has penetrated the housing
The remote control is off
Remote control battery drained
Battery too low
Remote control defective
Battery too low
Setting
1 Increase brightness
2 Reduce brightness
3 Switch off LED lamp
4 Switch on LED lamp
5 Colour fix
6 Flash mode: Flashing light
7 Strobe mode: Disco effect
8 Fade mode: Colour gradually fades into a different colour
9 Smooth mode: Smooth colour change
Solution
Position the LED lamp in direct sunlight for approx. 8 hours
Open the remote control on the back and replace the battery
Reduce the distance between the remote control and the LED lamp
Open the housing and let all components dry for several days. Check whether the lamp has rust
spots or damage to the components or battery, in this case dispose of the LED lamp.
Switch the remote control on by using the "ON" button
Open the remote control on the back and replace the battery
Position the LED lamp in direct sunlight for approx. 8 hours
Get in touch with your dealer
Position the LED lamp in direct sunlight for approx. 8 hours
1. Article name
2. Article number of device
3. Copy of the invoice
4. Error description
8