Bosch GWS 24-180 P Professional Manual Original página 20

20 | English
Angle Grinder
– with low-vibration auxili-
ary handle
– with standard auxiliary
handle
Protection class
The specifications apply to a rated voltage [U] of 230 V. These specifications may vary at different voltages and in country-
specific models.
Only for GWS 24-180 P and GWS 24-230 P:
The appliance meets IEC 61000-3-11 requirements and is subject to conditional connection. The appliance can lead to occa-
sional voltage fluctuations under unfavorable power conditions. The impedance of this appliance is set as Z
user must make sure, that the connection point, with the impedance Z
impedance requirement: Z ≥ Z
actual
thority.
Noise/Vibration Information
Noise emission values determined according to EN 60745-2-3.
Typically, the A-weighted noise level of the power tool is
Sound pressure level
Sound power level
Uncertainty K
Wear hearing protection!
Vibration total values a (triax vector sum) and uncertainty K determined according to EN 60745-2-3:
h
Surface grinding:
a
h
K
Disc sanding:
a
h
K
The vibration level given in these instructions has been
measured in accordance with a standardised measuring pro-
cedure and may be used to compare power tools. It can also
be used for a preliminary estimation of exposure to vibra-
tion.
The stated vibration level applies to the main applications of
the power tool. However, if the power tool is used for differ-
ent applications, with different application tools or poorly
maintained, the vibration level may differ. This can signific-
antly increase the exposure to vibration over the total work-
ing period.
To estimate the exposure to vibration accurately, the times
when the tool is switched off or when it is running but not ac-
tually being used should also be taken into account. This can
significantly reduce the exposure to vibration over the total
working period.
1 609 92A 88Z | (24.10.2022)
GWS 24-180 P GWS 24-230 P
kg 5.7
kg 5.6
/ II
. If Z is unknown, determine Z
max max
GWS 24-180 P GWS 24-230 P
3 601 HC2 1.. 3 601 HC3 1..
dB(A) 94
dB(A) 105
dB
3
2
m/s 6.5
2
m/s 1.5
2
m/s < 2.5
2
m/s 1.5
GWS 24-180 GWS 24-230
JZ
5.9 5.8
5.8 5.7
/ II / II
, on which the appliance shall be plugged in meets the
max
in consultation with the network supplier or supply au-
max
GWS 24-180 GWS 24-230
JZ
3 601 HC2 3.. 3 601 HC3 3..
94 94
105 105
3 3
6.5 6.5
1.5 1.5
< 2.5 3.0
1.5 1.5
Implement additional safety measures to protect the oper-
ator from the effects of vibration, such as servicing the
power tool and application tools, keeping the hands warm,
and organising workflows correctly.
Fitting
Fitting Protective Equipment
Pull the plug out of the socket before carrying out any
u
work on the power tool.
Note: If the grinding disc breaks during operation or the
holding fixtures on the protective guard/power tool become
damaged, the power tool must be sent to the after-sales ser-
vice immediately; see the "After-Sales Service and Applica-
tion Service" section for addresses.
GWS 24-230
JZ PZ
6.0 6.0
5.9 5.9
/ II / II
= 0.16 Ω. The
actual
GWS 24-230
JZ PZ
3 601 HC3 4..
94 94
105 105
3 3
6.5 6.5
1.5 1.5
3.0 3.0
1.5 1.5
Bosch Power Tools