EINHELL GE-HC 18 Li T Manual De Instrucciones página 13

5.2 Fitting the chain saw attachment (for use
as a pole chain saw)
5.2.a Assembly of the bar and the saw chain
•
Undo the chain tension lock knob (27) of the
chain wheel cover (Fig. 6).
•
Take off the chain wheel cover.
•
Lay the chain as shown in the groove which
runs around the chain saw bar (Fig. 7).
•
Insert the bar and chain as shown in the
mounting of the chain saw (Fig. 8). At the
same time guide the chain around the
sprocket wheel (Fig. 8/ Item 28).
•
Attach the chain wheel cover and fasten it
hand-tight with the chain tension lock knob
(Fig. 9/Item 27).
Do not fully tighten the chain tension lock knob
until after you have adjusted the chain tension
(see section 5.2.b.).
5.2.b Tensioning the saw chain
Caution! Always remove the battery from the
device before inspection and adjustment. Always
wear protective gloves when working on the chain
saw to protect yourself against injury.
•
Undo the chain tension lock knob (27) of the
chain wheel cover a few turns (Fig. 6).
•
Adjust the chain tension with the chain
tensioning wheel (Fig. 10/Item 29). Turning
the wheel clockwise increases the chain
tension, turning it counter-clockwise
decreases the chain tension. The saw chain
is correctly tensioned if it can be lifted approx.
0.08" (2 mm) in the middle of the bar (Fig. 11).
•
Tighten the chain tension lock knob (27) of
the chain wheel cover (Fig. 9).
Important! All the chain links must lie properly in
the guide groove of the bar.
Notes on tensioning the chain:
The chain must be properly tensioned to ensure
safe operation. When the saw chain can be raised
by around 0.08" (2 mm) in the middle of the bar,
you know that the chain tension is ideal. During
cutting, the temperature of the chain rises and
its length changes. It is important therefore to
check the chain tension at least every 10 minutes
and to adjust it again as required. This applies
in particular to new saw chains. When you have
fi nished working, slacken the chain again as it
will shorten when it cools down. This will help to
prevent damage to the chain.
Anl_GE_HC_18_Li_T_Part1_USA_SPK7.indb 13 Anl_GE_HC_18_Li_T_Part1_USA_SPK7.indb 13
EN
5.2.c Saw chain lubrication
Caution! Always remove the battery from the
device before inspection and adjustment. Always
wear protective gloves when working on the chain
saw to protect yourself against injury.
Important! Never operate the chain if it is not
lubricated with saw chain oil. Use of the chain saw
without saw chain oil or if the oil level is below the
viewing window will result in damage to the chain
saw!
Important! Be aware of the temperature
conditions:
Diff erent lubricants with completely diff erent
viscosities are required at diff erent ambient
temperatures. At lower temperatures you will need
low viscosity oils in order to achieve a suffi cient
lubricating fi lm. However, if the same low viscosity
oil is used during the summer it will become even
thinner due to the ambient temperatures alone,
and as a result the lubricating fi lm could break
down, causing the chain to overheat and become
damaged. In addition, the chain oil would burn
and produce unnecessary pollutants.
Filling the oil tank (Fig. 12):
•
Place the chain saw on a flat surface.
•
Clean the area around the oil tank cap (Fig.
12/Item 31) and then open the oil tank cap.
•
Fill the oil tank (Fig. 12/Item 30) with saw
chain oil. In the process, make sure that no
dirt enters the tank, as this could cause the oil
nozzle to become blocked.
•
Close the oil tank cap (Fig. 12/Item 31).
After the chain saw attachment has been fi tted
and when the equipment is not being used, slip
the chain saw guard (Fig. 1/Item 17) over the
mounted bar with saw chain in order to prevent
injuries.
5.3 Adjusting the additional handle (Fig. 13-
14)
a) Setting the tilt of the additional handle
Open the lock (22). Set the desired tilt of the
additional handle (8). Close the lock.
b) Shifting the additional handle
Open the lock and slide the additional handle (8)
into the required position. Close the lock.
5.4 Using the shoulder strap
Warning! Always use the shoulder strap when
working with the equipment. Switch off the
- 13 -
23.11.2022 14:22:54 23.11.2022 14:22:54