Publicidad
Idiomas disponibles
Idiomas disponibles
Timeshift Recording
In order to use timeshift recording feature the Time
Shift Mode option in the Record>Time Shift Mode
menu should be enabled first.
In timeshifting mode, the programme is paused
and simultaneously recorded to the connected USB
storage device. Press the Pause/Play button while
watching a broadcast to activate timeshifting mode.
Press the Pause/Play button again to resume the
paused programme from where you stopped. Press
the Stop button to stop timeshift recording and return
to the live broadcast.
When this feature is used for the first time Disk Setup
wizard will be displayed when the Pause/Play button is
pressed. You can either choose Auto or Manual setup
mode. In Manual mode, if you prefer, you can format
your USB storage device and specify the storage space
that will be used for timeshift function. When the setup
is complete, the Disk Setup Result will be displayed.
Press the OK button to exit.
Timeshift function will not be available for radio
broadcasts.
Disk Format
When using a new USB storage device, it is
recommended that you first format it using the Format
option in the Record>Device Info menu in Live TV
mode. Highlight the connected device on the Device
Info screen and press OK or Right directional button
to see the list of available options. Then highlight
Format and press OK to proceed. A confirmation
dialogue will be displayed. Highlight Yes and press
OK to start formatting.
IMPORTANT: Formatting your USB storage device
will erase ALL the data on it and its file system will be
converted to FAT32. In most cases operation errors will
be fixed after a format but you will lose ALL your data.
Schedule List
You can add reminders or record timers using the
Schedule List menu. You can access the Schedule
List from the Record menu in Live TV mode. Highlight
Schedule List and press OK. Previously set timers
will be listed if any available.
Press the Yellow button to add a timer while the
Schedule List menu is displayed on the screen. You
can define the type of the timer by setting the Schedule
Type option as Reminder or Record. When other
parameters are set press the Green button. The timer
will be added to the list.
If any available, you can also edit or delete the timers
on this list. Highlight the timer of your choice and press
the Red button to edit. After you edited the timer press
the Green button to save changes. Highlight the timer
of your choice and press the Blue button to delete.
When you choose to delete a timer a confirmation
dialogue will be displayed on the screen. Highlight Yes
and press OK to delete the selected timer.
A dialogue will be displayed if the time intervals of two
timers overlap. You can not set more than one timer
for the same time interval. To replace the old timer with
the new one, highlight Yes and press OK.
Press EXIT button to close the Schedule List.
CEC
With CEC function of your TV you can operate a
connected device with the TV remote control. This
function uses HDMI CEC (Consumer Electronics
Control) to communicate with the connected devices.
Devices must support HDMI CEC and must be
connected with an HDMI connection.
In order to make use of the CEC functionality the
related option in the menu should be switched on.
To check, switch on or off the CEC function, do the
following:
• Enter the Settings>Device Preferences>Inputs
menu on the Home Screen or TV options>Set-
tings>Device Preferences>Inputs menu in Live
TV mode.
• Scroll down to Consumer Electronic Control
(CEC) section. Check if the HDMI control option
is switched on.
• Highlight the HDMI control option and press OK to
switch on or off.
Make sure that all CEC settings are properly set up
on the connected CEC device. The CEC functionality
has different names on different brands. CEC function
might not work with all devices. If you connect a device
with HDMI CEC support to your TV, the related HDMI
input source will be renamed with the connected
device's name.
To operate the connected CEC device, select the
related HDMI input source from the Inputs menu on
the Home Screen. Or press the Source button and
select the related HDMI input source from the list.
To terminate this operation and control the TV via
the remote again, press the Source button, which
will still be functional, on the remote and switch to
another source.
The TV remote is automatically able to control the
device once the connected HDMI source has been
selected. However not all buttons will be forwarded
to the device. Only devices that support CEC Remote
Control function will respond to the TV remote control.
The TV supports also ARC (Audio Return Channel)
feature. This feature is an audio link meant to replace
other cables between the TV and the audio system
(A/V receiver or speaker system). Connect the audio
English - 25 -
Publicidad
